xe34-openwrt-console-log

xe34-openwrt-console-log.log

[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x51af8014]
[    0.000000] Linux version 6.6.32 (nuc@nuc) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 13.3.0 r26467-50e26e6fd7) 13.3.0, GNU ld (GNU Binutils) 2.42) #0 SMP Thu May 30 20:47:59 2024
[    0.000000] Machine model: Cambium Networks XE3-4
[    0.000000] OF: reserved mem: 0x0000000000060000..0x0000000000065fff (24 KiB) nomap non-reusable memory@60000
[    0.000000] OF: reserved mem: 0x000000004a100000..0x000000004a4fffff (4096 KiB) nomap non-reusable bootloader@4a100000
[    0.000000] OF: reserved mem: 0x000000004a500000..0x000000004a5fffff (1024 KiB) nomap non-reusable sbl@4a500000
[    0.000000] OF: reserved mem: 0x000000004a600000..0x000000004a9fffff (4096 KiB) nomap non-reusable memory@4a600000
[    0.000000] OF: reserved mem: 0x000000004aa00000..0x000000004aafffff (1024 KiB) nomap non-reusable memory@4aa00000
[    0.000000] OF: reserved mem: 0x000000004ab00000..0x000000004fffffff (87040 KiB) nomap non-reusable memory@4ab00000
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000040000000-0x000000007fffffff]
[    0.000000]   DMA32    empty
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000040000000-0x000000004a0fffff]
[    0.000000]   node   0: [mem 0x000000004a100000-0x000000004fffffff]
[    0.000000]   node   0: [mem 0x0000000050000000-0x000000007fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff]
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.0
[    0.000000] percpu: Embedded 18 pages/cpu s35240 r8192 d30296 u73728
[    0.000000] pcpu-alloc: s35240 r8192 d30296 u73728 alloc=18*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: Spectre-v4
[    0.000000] alternatives: applying boot alternatives
[    0.000000] Kernel command line: console=ttyMSM0,115200n8 cnss2.bdf_pci0=0xab ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait root=/dev/ubiblock0_1
[    0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 258048
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted to 1MB
[    0.000000] software IO TLB: area num 4.
[    0.000000] software IO TLB: mapped [mem 0x000000007eb00000-0x000000007ec00000] (1MB)
[    0.000000] Memory: 916900K/1048576K available (7872K kernel code, 880K rwdata, 2356K rodata, 1472K init, 276K bss, 131676K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] 	Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] Root IRQ handler: gic_handle_irq
[    0.000000] GICv2m: range[mem 0x0b00a000-0x0b00affc], SPI[448:479]
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000] arch_timer: cp15 and mmio timer(s) running at 24.00MHz (virt/virt).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000000] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.000073] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.000086] pid_max: default: 32768 minimum: 301
[    0.005114] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.005128] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.009369] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1.
[    0.009595] rcu: Hierarchical SRCU implementation.
[    0.009599] rcu: 	Max phase no-delay instances is 1000.
[    0.010374] smp: Bringing up secondary CPUs ...
[    0.011059] Detected VIPT I-cache on CPU1
[    0.011153] CPU1: Booted secondary processor 0x0000000001 [0x51af8014]
[    0.011835] Detected VIPT I-cache on CPU2
[    0.011904] CPU2: Booted secondary processor 0x0000000002 [0x51af8014]
[    0.012579] Detected VIPT I-cache on CPU3
[    0.012645] CPU3: Booted secondary processor 0x0000000003 [0x51af8014]
[    0.012714] smp: Brought up 1 node, 4 CPUs
[    0.012722] SMP: Total of 4 processors activated.
[    0.012727] CPU features: detected: 32-bit EL0 Support
[    0.012731] CPU features: detected: CRC32 instructions
[    0.012802] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[    0.012810] CPU: All CPU(s) started at EL1
[    0.012812] alternatives: applying system-wide alternatives
[    0.020829] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.020851] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.022563] pinctrl core: initialized pinctrl subsystem
[    0.024272] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.024895] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[    0.024946] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.024979] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.025337] thermal_sys: Registered thermal governor 'step_wise'
[    0.025397] cpuidle: using governor menu
[    0.025620] ASID allocator initialised with 65536 entries
[    0.029753] OF: /soc@0/wifi@c000000: #nvmem-cell-cells = 1 found 0
[    0.073970] Modules: 29504 pages in range for non-PLT usage
[    0.073982] Modules: 521024 pages in range for PLT usage
[    0.079200] SCSI subsystem initialized
[    0.079418] usbcore: registered new interface driver usbfs
[    0.079467] usbcore: registered new interface driver hub
[    0.079522] usbcore: registered new device driver usb
[    0.079795] qcom_scm: convention: smc arm 64
[    0.081277] clocksource: Switched to clocksource arch_sys_counter
[    0.085043] NET: Registered PF_INET protocol family
[    0.085203] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.087774] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[    0.087797] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.087812] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.087898] TCP bind hash table entries: 8192 (order: 6, 262144 bytes, linear)
[    0.088167] TCP: Hash tables configured (established 8192 bind 8192)
[    0.088265] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.088303] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.088750] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.088801] PCI: CLS 0 bytes, default 64
[    0.090330] workingset: timestamp_bits=46 max_order=18 bucket_order=0
[    0.090864] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.090871] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.098465] qcom-qusb2-phy 59000.qusb: supply vdd not found, using dummy regulator
[    0.098630] qcom-qusb2-phy 59000.qusb: supply vdda-pll not found, using dummy regulator
[    0.098672] qcom-qusb2-phy 59000.qusb: supply vdda-phy-dpdm not found, using dummy regulator
[    0.098850] qcom-qusb2-phy 59000.qusb: Registered Qcom-QUSB2 phy
[    0.100269] qcom-pcie 20000000.pci: host bridge /soc@0/pci@20000000 ranges:
[    0.100329] qcom-pcie 20000000.pci:       IO 0x0020200000..0x002020ffff -> 0x0000000000
[    0.100355] qcom-pcie 20000000.pci:      MEM 0x0020220000..0x002fffffff -> 0x0020220000
[    0.107584] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.108562] msm_serial 78b1000.serial: msm_serial: detected port #0
[    0.108613] msm_serial 78b1000.serial: uartclk = 1843199
[    0.108938] 78b1000.serial: ttyMSM0 at MMIO 0x78b1000 (irq = 21, base_baud = 115199) is a MSM
[    0.108971] msm_serial: console setup on port #0
[    0.109041] printk: console [ttyMSM0] enabled
[    0.212971] qcom-pcie 20000000.pci: iATU: unroll T, 8 ob, 8 ib, align 4K, limit 1024G
[    0.215989] msm_serial: driver initialized
[    0.311282] qcom-pcie 20000000.pci: PCIe Gen.3 x1 link up
[    0.863846] qcom-pcie 20000000.pci: PCI host bridge to bus 0000:00
[    0.868978] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.875066] pci_bus 0000:00: root bus resource [io  0x0000-0xffff]
[    0.880520] pci_bus 0000:00: root bus resource [mem 0x20220000-0x2fffffff]
[    0.886723] pci 0000:00:00.0: [17cb:1003] type 01 class 0x060400
[    0.893561] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00000fff]
[    0.899761] pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
[    0.908396] pci 0000:01:00.0: [17cb:1104] type 00 class 0x028000
[    0.912047] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]
[    0.918524] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold
[    0.924858] pci 0000:01:00.0: 7.876 Gb/s available PCIe bandwidth, limited by 8.0 GT/s PCIe x1 link at 0000:00:00.0 (capable of 15.752 Gb/s with 8.0 GT/s PCIe x2 link)
[    0.931270] pci 0000:00:00.0: BAR 8: assigned [mem 0x20400000-0x205fffff]
[    0.945552] pci 0000:00:00.0: BAR 0: assigned [mem 0x20220000-0x20220fff]
[    0.952500] pci 0000:01:00.0: BAR 0: assigned [mem 0x20400000-0x205fffff 64bit]
[    0.959296] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[    0.966382] pci 0000:00:00.0:   bridge window [mem 0x20400000-0x205fffff]
[    0.974267] pcieport 0000:00:00.0: PME: Signaling with IRQ 24
[    0.978797] pcieport 0000:00:00.0: AER: enabled with IRQ 24
[    0.989596] loop: module loaded
[    0.990886] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xaa
[    0.992864] nand: Macronix MX30UF2G18AC
[    0.999350] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[    1.002944] qcom-nandc 79b0000.nand-controller: Opcode not supported: 238
[    1.010556] Block protection check failed
[    1.017719] 4 fixed-partitions partitions found on MTD device qcom_nand.0
[    1.021421] Creating 4 MTD partitions on "qcom_nand.0":
[    1.028174] 0x000000000000-0x000006000000 : "rootfs"
[    1.102953] mtd: setting mtd0 (rootfs) as root device
[    1.103239] mtdsplit: no squashfs found in "rootfs"
[    1.107000] 0x000006000000-0x00000c000000 : "rootfs_1"
[    1.182656] 0x00000c000000-0x00000f000000 : "NVRAM"
[    1.218671] 0x00000f000000-0x000010000000 : "crashLog"
[    1.233506] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[    1.234349] spi-nor spi0.0: found w25q128fw, expected n25q128a11
[    1.240605] spi-nor spi0.0: w25q128fw (16384 Kbytes)
[    1.245953] 16 fixed-partitions partitions found on MTD device spi0.0
[    1.250889] Creating 16 MTD partitions on "spi0.0":
[    1.256923] 0x000000000000-0x0000000c0000 : "0:SBL1"
[    1.262172] 0x0000000c0000-0x0000000d0000 : "0:MIBIB"
[    1.267261] 0x0000000d0000-0x0000000f0000 : "0:BOOTCONFIG"
[    1.272233] 0x0000000f0000-0x000000110000 : "0:BOOTCONFIG1"
[    1.277566] 0x000000110000-0x0000002b0000 : "0:QSEE"
[    1.283091] 0x0000002b0000-0x000000450000 : "0:QSEE_1"
[    1.288271] 0x000000450000-0x000000460000 : "0:DEVCFG"
[    1.293297] 0x000000460000-0x000000470000 : "mfginfo"
[    1.298322] 0x000000470000-0x0000004b0000 : "0:RPM"
[    1.303489] 0x0000004b0000-0x0000004f0000 : "0:RPM_1"
[    1.308140] 0x0000004f0000-0x000000500000 : "0:CDT"
[    1.313414] 0x000000500000-0x000000510000 : "0:CDT_1"
[    1.318037] 0x000000510000-0x000000520000 : "0:APPSBLENV"
[    1.323267] 0x000000520000-0x0000005c0000 : "0:APPSBL"
[    1.328646] 0x0000005c0000-0x000000660000 : "0:APPSBL_1"
[    1.333672] 0x000000660000-0x0000006e0000 : "0:ART"
[    1.603384] i2c_dev: i2c /dev entries driver
[    1.609244] sdhci: Secure Digital Host Controller Interface driver
[    1.609281] sdhci: Copyright(c) Pierre Ossman
[    1.614341] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.619169] sdhci_msm 7804000.mmc: Got CD GPIO
[    1.621775] remoteproc remoteproc0: releasing cd00000.remoteproc
[    1.625601] mmc0: CQHCI version 5.10
[    1.647244] NET: Registered PF_INET6 protocol family
[    1.648387] Segment Routing with IPv6
[    1.651357] In-situ OAM (IOAM) with IPv6
[    1.654934] NET: Registered PF_PACKET protocol family
[    1.658862] 8021q: 802.1Q VLAN Support v1.8
[    1.667885] mmc0: SDHCI controller on 7804000.mmc [7804000.mmc] using ADMA 64-bit
[    1.667936] sdhci_msm 7804000.mmc: mmc0: CQE init: success
[    1.696344] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 799999 KHz, changing to: 864000 KHz
[    1.698403] remoteproc remoteproc0: cd00000.remoteproc is available
[    1.706335] ubi0: attaching mtd0
[    2.137565] ubi0: scanning is finished
[    2.144037] ubi0: attached mtd0 (name "rootfs", size 96 MiB)
[    2.144075] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
[    2.148769] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
[    2.155471] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[    2.162318] ubi0: good PEBs: 768, bad PEBs: 0, corrupted PEBs: 0
[    2.169081] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128
[    2.175341] ubi0: max/mean erase counter: 21/13, WL threshold: 4096, image sequence number: 1713778025
[    2.182384] ubi0: available PEBs: 0, total reserved PEBs: 768, PEBs reserved for bad PEB handling: 40
[    2.191671] ubi0: background thread "ubi_bgt0d" started, PID 590
[    2.192438] block ubiblock0_1: created from ubi0:1(rootfs)
[    2.207118] clk: Disabling unused clocks
[    2.215136] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
[    2.215623] Freeing unused kernel memory: 1472K
[    2.221373] Run /sbin/init as init process
[    2.225587]   with arguments:
[    2.225589]     /sbin/init
[    2.225591]   with environment:
[    2.225593]     HOME=/
[    2.225595]     TERM=linux
[    2.388425] init: Console is alive
[    2.388548] init: - watchdog -
[    2.761296] random: crng init done
[    2.911397] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    2.938203] gpio_button_hotplug: loading out-of-tree module taints kernel.
[    2.971248] ssdk_dt_parse_port_bmp[1056]:INFO:port_bmp doesn't exist!
[    2.971329] ssdk_dt_parse_interrupt[934]:INFO:intr-gpio does not exist
[    3.391694] __adpt_hppe_uniphy_psgmii_mode_set[1194]:INFO:uniphy 0 psgmii channel selection
[    3.517408] regi_init[2525]:INFO:Initializing CPPE Done!!
[    3.517513] regi_init[2574]:INFO:qca-ssdk module init succeeded!
[    3.523803] EDMA ver 1 hw init
[    3.528072] EDMA HW Reset completed succesfully
[    3.530744] Num rings - TxDesc:1 (23-23) TxCmpl:1 (23-23)
[    3.535182] RxDesc:1 (15-15) RxFill:1 (7-7)
[    3.541007] dp4: ppe offload disabled: 0 for macid 4
[    3.544703] dp4: Switch attached to macid 4 status: 0
[    3.743322] Qualcomm QCA8072 90000.mdio-1:03: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:03, irq=POLL)
[    3.744204] dp5: ppe offload disabled: 0 for macid 5
[    3.752228] dp5: Switch attached to macid 5 status: 0
[    3.907144] Qualcomm QCA8081 90000.mdio-1:18: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:18, irq=POLL)
[    3.907956] **********************************************************
[    3.916049] * NSS Data Plane driver
[    3.922548] **********************************************************
[    3.932787] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    3.942134] init: - preinit -
[    6.447136] UBIFS (ubi0:2): Mounting in unauthenticated mode
[    6.447249] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 753
[    6.521948] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
[    6.521987] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
[    6.528766] UBIFS (ubi0:2): FS size: 75677696 bytes (72 MiB, 596 LEBs), max 606 LEBs, journal size 3809280 bytes (3 MiB, 30 LEBs)
[    6.538687] UBIFS (ubi0:2): reserved for root: 3574443 bytes (3490 KiB)
[    6.550298] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID F6CDF012-3A79-40FD-A9D2-7B6F1FF125DF, small LPT model
[    6.557759] mount_root: overlay filesystem has not been fully initialized yet
[    6.568542] mount_root: switching to ubifs overlay
[    6.578398] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off.
[    6.707191] urandom-seed: Seed file not found (/etc/urandom.seed)
[    6.759576] procd: - early -
[    6.759693] procd: - watchdog -
[    7.318524] procd: - watchdog -
[    7.318758] procd: - ubus -
[    7.475175] procd: - init -
[    7.694573] kmodloader: loading kernel modules from /etc/modules.d/*
[    7.783521] GACT probability on
[    7.784055] Mirror/redirect action on
[    7.788554] u32 classifier
[    7.789282]     input device check on
[    7.791907]     Actions configured
[    7.802297] Loading modules backported from Linux version v6.6.15-0-g51f354b815c4
[    7.802334] Backport generated by backports.git 193becf2
[    7.815873] NET: Registered PF_QIPCRTR protocol family
[    7.864392] ath11k c000000.wifi: ipq6018 hw1.0
[    7.864422] ath11k c000000.wifi: FW memory mode: 0
[    7.867954] remoteproc remoteproc0: powering up cd00000.remoteproc
[    7.877434] urngd: v1.0.2 started.
[    7.885651] remoteproc remoteproc0: Booting fw image IPQ6018/q6_fw.mdt, size 7340
[    8.691866] remoteproc remoteproc0: remote processor cd00000.remoteproc is now up
[    8.693204] ath11k c000000.wifi: qmi ignore invalid mem req type 3
[    8.698865] ath11k_pci 0000:01:00.0: BAR 0: assigned [mem 0x20400000-0x205fffff 64bit]
[    8.698891] ath11k c000000.wifi: chip_id 0x0 chip_family 0x4 board_id 0xff soc_id 0xffffffff
[    8.704495] ath11k_pci 0000:01:00.0: enabling device (0000 -> 0002)
[    8.712317] ath11k c000000.wifi: fw_version 0x25008f8e fw_build_timestamp 2024-03-01 03:54 fw_build_id WLAN.HK.2.5.0.1-03982-QCAHKSWPL_SILICONZ-3
[    8.721465] ath11k_pci 0000:01:00.0: MSI vectors: 16
[    8.740131] ath11k_pci 0000:01:00.0: qcn9074 hw1.0
[    8.745135] ath11k_pci 0000:01:00.0: FW memory mode: 0
[    8.906860] mhi mhi0: Requested to power ON
[    8.906902] mhi mhi0: Power on setup success
[    9.531311] mhi mhi0: Wait for device to enter SBL or Mission mode
[    9.815427] kmodloader: done loading kernel modules from /etc/modules.d/*
[    9.838453] ath11k_pci 0000:01:00.0: chip_id 0x0 chip_family 0x0 board_id 0xff soc_id 0xffffffff
[    9.838498] ath11k_pci 0000:01:00.0: fw_version 0x270206d0 fw_build_timestamp 2022-08-04 12:48 fw_build_id WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
[   12.445054] br-lan: port 1(lan1) entered blocking state
[   12.445096] br-lan: port 1(lan1) entered disabled state
[   12.449127] nss-dp 3a001800.dp5 lan1: entered allmulticast mode
[   12.454522] nss-dp 3a001800.dp5 lan1: entered promiscuous mode
[   12.471868] br-lan: port 2(lan2) entered blocking state
[   12.471911] br-lan: port 2(lan2) entered disabled state
[   12.475942] nss-dp 3a001600.dp4 lan2: entered allmulticast mode
[   12.481339] nss-dp 3a001600.dp4 lan2: entered promiscuous mode
[   15.592295] nss-dp 3a001800.dp5 lan1: PHY Link up speed: 1000
[   15.592388] br-lan: port 1(lan1) entered blocking state
[   15.597030] br-lan: port 1(lan1) entered forwarding state