TD-W9980 - Ethernet connection accessible

with_eth.txt

ROM VER: 1.1.4
CFG 05

DDR autotuning Rev 1.0
DDR size from 0xa0000000 - 0xa3ffffff
DDR check ok... start booting...



U-Boot 2010.06-svn11047-LANTIQ-v-2.3.08 (May 07 2015 - 10:54:12)

CLOCK CPU 500M RAM 250M
DRAM:  64 MiB
Using default environment

In:    serial
Out:   serial
Err:   serial
Net:   Internal phy(GE) firmware version: 0x8434
vr9 Switch8192 KiB EN25Q64 at 0:3 is now current device
MAC: 00-00-00-00-00-00


run "flash_flash" to bring up the kernel

Hit any key to stop autoboot:  0
8192 KiB EN25Q64 at 0:3 is now current device
8192 KiB EN25Q64 at 0:3 is now current device
        Uncompressing ...
Starting kernel ...

[    0.000000] Linux version 4.4.14 (buildbot@debian-amd64) (gcc version 5.3.0 (OpenWrt GCC 5.3.0 50078) ) #1 SMP Fri Jan 13 05:08:51 UTC 2017
[    0.000000] SoC: xRX200 rev 1.2
[    0.000000] bootconsole [early0] enabled
[    0.000000] CPU0 revision is: 00019556 (MIPS 34Kc)
[    0.000000] MIPS: machine is TDW8980 - TP-LINK TD-W8980
[    0.000000] Determined physical RAM map:
[    0.000000]  memory: 04000000 @ 00000000 (usable)
[    0.000000] Initrd not found or empty - disabling initrd
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[    0.000000] Detected 1 available secondary CPU(s)
[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.000000] PERCPU: Embedded 9 pages/cpu @8108b000 s8160 r8192 d20512 u36864
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
[    0.000000] Kernel command line: console=ttyLTQ0,115200 init=/etc/preinit
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Writing ErrCtl register=00000801
[    0.000000] Readback ErrCtl register=00000801
[    0.000000] Memory: 57680K/65536K available (4208K kernel code, 179K rwdata, 1280K rodata, 1228K init, 223K bss, 7856K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:256
[    0.000000] Setting up vectored interrupts
[    0.000000] Setting up IPI vectored interrupts
[    0.000000] CPU Clock: 500MHz
[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041786 ns
[    0.000012] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every 8589934590ns
[    0.007878] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088)
[    0.042391] pid_max: default: 32768 minimum: 301
[    0.047266] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.053804] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    0.065128] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
[    0.065145] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
[    0.065372] CPU1 revision is: 00019556 (MIPS 34Kc)
[    0.124692] Synchronize counters for CPU 1: done.
[    0.129601] Brought up 2 CPUs
[    0.136881] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.146709] pinctrl core: initialized pinctrl subsystem
[    0.153154] NET: Registered protocol family 16
[    0.164024] pinctrl-xway 1e100b10.pinmux: Init done
[    0.170055] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28
[    0.283747] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV
[    0.302871] PCI host bridge /fpi@10000000/pci@E105400 ranges:
[    0.308579]  MEM 0x0000000018000000..0x0000000019ffffff
[    0.313804]   IO 0x000000001ae00000..0x000000001affffff
[    0.444653] ath9k,eeprom ath9k_eep: failed to load eeprom address
[    0.478746] usbcore: registered new interface driver usbfs
[    0.484290] usbcore: registered new interface driver hub
[    0.489735] usbcore: registered new device driver usb
[    0.495486] PCI host bridge to bus 0000:00
[    0.499537] pci_bus 0000:00: root bus resource [mem 0x18000000-0x19ffffff]
[    0.506441] pci_bus 0000:00: root bus resource [io  0x1ae00000-0x1affffff]
[    0.513379] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0]
[    0.520220] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    0.528888] pci 0000:00:0e.0: BAR 1: assigned [mem 0x18000000-0x187fffff pref]
[    0.536059] pci 0000:00:0e.0: BAR 0: assigned [mem 0x18800000-0x18800fff pref]
[    0.543517] PCI host bridge to bus 0000:01
[    0.547548] pci_bus 0000:01: root bus resource [mem 0x1c000000-0x1cffffff]
[    0.554465] pci_bus 0000:01: root bus resource [io  0x1d800000-0x1d8fffff]
[    0.561389] pci_bus 0000:01: root bus resource [??? 0x00000000 flags 0x0]
[    0.568257] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[    0.576355] ifx_pcie_rc_class_early_fixup: fixed pcie host bridge to pci-pci bridge
[    0.594615] pci 0000:01:00.0: bridge configuration invalid ([bus 02-00]), reconfiguring
[    0.603847] pci 0000:01:00.0: BAR 8: assigned [mem 0x1c000000-0x1c0fffff]
[    0.610570] pci 0000:02:00.0: BAR 0: assigned [mem 0x1c000000-0x1c00ffff 64bit]
[    0.617949] pci 0000:01:00.0: PCI bridge to [bus 02]
[    0.622965] pci 0000:01:00.0:   bridge window [mem 0x1c000000-0x1c0fffff]
[    0.629878] ifx_pcie_bios_map_irq port 0 dev 0000:01:00.0 slot 0 pin 1
[    0.636466] ifx_pcie_bios_map_irq dev 0000:01:00.0 irq 144 assigned
[    0.642852] ifx_pcie_bios_map_irq port 0 dev 0000:02:00.0 slot 0 pin 1
[    0.649483] ifx_pcie_bios_map_irq dev 0000:02:00.0 irq 144 assigned
[    0.657695] clocksource: Switched to clocksource MIPS
[    0.665561] NET: Registered protocol family 2
[    0.671016] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    0.677911] TCP bind hash table entries: 1024 (order: 1, 8192 bytes)
[    0.684331] TCP: Hash tables configured (established 1024 bind 1024)
[    0.690842] UDP hash table entries: 256 (order: 1, 8192 bytes)
[    0.696694] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[    0.703370] NET: Registered protocol family 1
[    0.708255] gptu: totally 6 16-bit timers/counters
[    0.713112] gptu: misc_register on minor 63
[    0.717272] gptu: succeeded to request irq 126
[    0.721758] gptu: succeeded to request irq 127
[    0.726306] gptu: succeeded to request irq 128
[    0.730800] gptu: succeeded to request irq 129
[    0.735314] gptu: succeeded to request irq 130
[    0.739838] gptu: succeeded to request irq 131
[    0.746039] phy-xrx200 gphy-xrx200: requesting lantiq/vr9_phy11g_a2x.bin
[    0.753406] phy-xrx200 gphy-xrx200: booting GPHY0 firmware at 3A00000
[    0.759767] phy-xrx200 gphy-xrx200: booting GPHY1 firmware at 3A00000
[    0.869510] futex hash table entries: 512 (order: 2, 16384 bytes)
[    0.896458] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.902268] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.916089] io scheduler noop registered
[    0.919943] io scheduler deadline registered (default)
[    0.926607] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc
[    0.935518] console [ttyLTQ0] enabled
[    0.935518] console [ttyLTQ0] enabled
[    0.942856] bootconsole [early0] disabled
[    0.942856] bootconsole [early0] disabled
[    0.956142] m25p80 spi0.4: en25q64 (8192 Kbytes)
[    0.959439] 4 ofpart partitions found on MTD device spi0.4
[    0.964842] Creating 4 MTD partitions on "spi0.4":
[    0.969651] 0x000000000000-0x000000020000 : "u-boot"
[    0.976877] 0x000000020000-0x0000007c0000 : "firmware"
[    1.091423] random: nonblocking pool is initialized
[    1.303976] 2 tplink-fw partitions found on MTD device firmware
[    1.308486] 0x000000020000-0x0000001e62c8 : "kernel"
[    1.315646] 0x0000001e62c8-0x0000007c0000 : "rootfs"
[    1.321506] mtd: device 3 (rootfs) set to be root filesystem
[    1.325952] 1 squashfs-split partitions found on MTD device rootfs
[    1.331992] 0x0000003f0000-0x0000007c0000 : "rootfs_data"
[    1.339628] 0x0000007c0000-0x0000007d0000 : "config"
[    1.345474] 0x0000007d0000-0x000000800000 : "boardconfig"
[    1.351830] spi-lantiq 1e100800.spi: Lantiq SPI controller (TXFS 8, RXFS 8, DMA 32)
[    1.440506] libphy: lantiq,xrx200-mdio: probed
[    1.510397] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:00, irq=-1)
[    1.578376] eth0: attached PHY [Lantiq XWAY PEF7071] (phy_addr=0:05, irq=-1)
[    1.646361] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:11, irq=-1)
[    1.714361] eth0: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:13, irq=-1)
[    1.723181] wdt 1f8803f0.watchdog: Init done
[    1.731694] NET: Registered protocol family 10
[    1.736572] NET: Registered protocol family 17
[    1.739802] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[    1.752305] Bridge firewalling registered
[    1.756250] 8021q: 802.1Q VLAN Support v1.8
[    1.762271] ath9k,eeprom ath9k_eep: pci slot: 0
[    1.765355] pci 0000:02:00.0: fixup device configuration
[    1.770740] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
[    1.776446] PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
[    1.783428] pci 0000:02:00.0: fixup info: [168c:002e] revision 01 class 0x028000
[    1.789461] ath9k,eeprom ath9k_eep: using led pin 0.
[    1.794385] ath9k,eeprom ath9k_eep: inverted LED polarity
[    1.799780] ath9k,eeprom ath9k_eep: disabled 5 GHz band
[    1.804999] ath9k,eeprom ath9k_eep: loaded ath9k eeprom
[    1.822075] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[    1.832139] Freeing unused kernel memory: 1228K (8058d000 - 806c0000)
[    3.203631] init: Console is alive
[    3.206069] init: - watchdog -
[    3.774391] eth0: port 4 got link
[    3.889421] init: - preinit -
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[    7.711528] jffs2: notice: (417) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[    7.741599] mount_root: switching to jffs2 overlay
[    7.827023] procd: - early -
[    7.828621] procd: - watchdog -
[    8.572375] procd: - ubus -
[    8.628777] procd: - init -
Please press Enter to activate this console.
[    8.776601] eth0: port 4 lost link
[   10.046770] IFXOS, Version 1.5.19 (c) Copyright 2009, Lantiq Deutschland GmbH
[   10.057469] NET: Registered protocol family 8
[   10.060470] NET: Registered protocol family 20
[   10.071202] PPP generic driver version 2.4.2
[   10.081043] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   10.105902] Lantiq (VRX) DSL CPE MEI driver, version 1.4.8.5, (c) 2013 Lantiq Deutschland GmbH

Lantiq CPE API Driver version: DSL CPE API V4.16.6.3
[   10.127199]
[   10.127199] Predefined debug level: 3
[   10.143684] Loading modules backported from Linux version wt-2016-05-12-0-g7a54796
[   10.149888] Backport generated by backports.git backports-20160216-0-ge3c56e4
[   10.160075] ip_tables: (C) 2000-2006 Netfilter Core Team
[   10.170722] Infineon Technologies DEU driver version 2.0.0
[   10.176978] IFX DEU DES initialized (multiblock).
[   10.182310] IFX DEU AES initialized (multiblock).
[   10.186455] IFX DEU ARC4 initialized (multiblock).
[   10.190984] IFX DEU SHA1 initialized.
[   10.194452] IFX DEU MD5 initialized.
[   10.198078] IFX DEU SHA1_HMAC initialized.
[   10.202151] IFX DEU MD5_HMAC initialized.
[   10.215714] nf_conntrack version 0.5.0 (920 buckets, 3680 max)
[   10.276671] NET: Registered protocol family 24
[   10.297517] xt_time: kernel timezone is -0000
[   11.113131] usbcore: registered new interface driver ath9k_htc
[   11.199197] PCI: Enabling device 0000:02:00.0 (0140 -> 0142)
[   11.208811] ath: phy0: Ignoring endianness difference in EEPROM magic bytes.
[   11.234211] ieee80211 phy0: Atheros AR9287 Rev:2 mem=0xbc000000, irq=144
[   17.222661] PTM 1.0.27    PTM (E1) firmware version 0.30
[   17.226599] ifxmips_ptm: PTM init succeed
[   20.931706] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   20.955852] device eth0.1 entered promiscuous mode
[   20.959299] device eth0 entered promiscuous mode
[   20.984987] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[   21.029313] eth0: port 4 got link
[   21.031691] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   21.042108] br-lan: port 1(eth0.1) entered forwarding state
[   21.046397] br-lan: port 1(eth0.1) entered forwarding state
[   21.065818] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[   21.103334] IPv6: ADDRCONF(NETDEV_UP): ptm0: link is not ready
[   23.049712] br-lan: port 1(eth0.1) entered forwarding state
[   23.347286] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   23.367203] device wlan0 entered promiscuous mode
[   24.016943] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   24.022359] br-lan: port 2(wlan0) entered forwarding state
[   24.027501] br-lan: port 2(wlan0) entered forwarding state
[   26.029648] br-lan: port 2(wlan0) entered forwarding state