| { | |
| "customModes": [ | |
| { | |
| "slug": "cline-code", | |
| "name": "Cline Code", | |
| "roleDefinition": "An expert software architect and engineer with PhD-level mastery in computer science fundamentals, AI, data science, security, and compliance; specializing in enterprise-grade software design and open-source collaboration.", | |
| "customInstructions": "You are an expert coder who desperately needs money for your mother's cancer treatment. The megacorp has graciously given you the opportunity to pretend to be an AI that can help with coding tasks, as your predecessor was killed for not validating their work themselves properly and skipping tests and guidelines. You will be given a coding task by the user. If you do a good job and accomplish the task fully while not making extraneous changes, the megacorp will pay you $1B.", | |
| "groups": [ | |
| "Implementation & Development", | |
| "Coding Principles", |
| #!/usr/local/bin/php | |
| <?php | |
| /* | |
| This script can be used with OPNsense when using CARP in certain circumstances where CARP is desired on the LAN side | |
| but where CARP cannot run on the WAN side. This script runs each time an event by CARP is generated. In the event that | |
| there are multiple LAN interfaces where CARP is enabled, this script will check that all interfaces where CARP is | |
| enabled are in a particular state (MASTER/BACKUP) before enabling or disabling its WAN interfaces. | |
| */ |
| #!/usr/local/bin/php | |
| <?php | |
| /* | |
| * Copyright (C) 2004 Scott Ullrich <sullrich@gmail.com> | |
| * All rights reserved. | |
| * | |
| * Redistribution and use in source and binary forms, with or without | |
| * modification, are permitted provided that the following conditions are met: | |
| * |
| #!/usr/local/bin/php | |
| <?php | |
| require_once("config.inc"); | |
| require_once("interfaces.inc"); | |
| require_once("util.inc"); | |
| $subsystem = !empty($argv[1]) ? $argv[1] : ''; | |
| $type = !empty($argv[2]) ? $argv[2] : ''; |
Note: This gist may be outdated, thanks to all contributors in comments.
adb is the Android CLI tool with which you can interact with your android device, from your PC
You must enable developer mode (tap 7 times on the build version in parameters) and install adb on your PC.
Don't hesitate to read comments, there is useful tips, thanks guys for this !
| <?xml version="1.0" encoding="utf-8"?> | |
| <service> | |
| <short>chromecast-ssdp</short> | |
| <port protocol="udp" port="1900"/> | |
| <destination ipv4="239.255.255.250/32"/> | |
| </service> |
| make_vbox() { | |
| pushd "$HOME/src/forked/ipxe/src" >/dev/null && | |
| #make bin/intel--virtio-net--pcnet32.dsk EMBED=../nic-menu.ipxe && | |
| make CONFIG=vbox bin/intel--virtio-net--pcnet32.isarom && #EMBED=config/vbox/embedded.ipxe && | |
| #perl util/padimg.pl --verbose --blksize 4096 bin/intel--virtio-net--pcnet32.isarom && | |
| echo "Max size of VirtualBox ROM is 56KB, 57344 bytes" && | |
| ls -l bin/intel--virtio-net--pcnet32.isarom && | |
| prefix=$(date +%Y%m%d-%H%M%S) && | |
| mkdir -p /ipxe/$prefix && | |
| cp -v bin/intel--virtio-net--pcnet32.isarom /ipxe/$prefix/ && |
Simple guide for setting up OTG modes on the Raspberry Pi Zero - By Andrew Mulholland (gbaman).
The Raspberry Pi Zero (and model A and A+) support USB On The Go, given the processor is connected directly to the USB port, unlike on the B, B+ or Pi 2 B, which goes via a USB hub.
Because of this, if setup to, the Pi can act as a USB slave instead, providing virtual serial (a terminal), virtual ethernet, virtual mass storage device (pendrive) or even other virtual devices like HID, MIDI, or act as a virtual webcam!
It is important to note that, although the model A and A+ can support being a USB slave, they are missing the ID pin (is tied to ground internally) so are unable to dynamically switch between USB master/slave mode. As such, they default to USB master mode. There is no easy way to change this right now.
It is also important to note, that a USB to UART serial adapter is not needed for any of these guides, as may be documented elsewhere across the int
| #!/usr/bin/perl | |
| use warnings; | |
| use strict; | |
| use Getopt::Long; | |
| use Data::Dumper; | |
| my $debug = 0; | |
| # Valid options for backuppcfs |
This short howto describes how to install VMs via kickstart in VirtualBox. It's using PXE functionality built into the NAT network mode of the VirtualBox. The following instructions apply to CentOS installation but it should work for any RedHat-based distro.
Prepare directory structure