RB5

kona-rb5.dtsi

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>

#include "kona-pmic-overlay.dtsi"
#include "kona-sde-display.dtsi"
#include "camera/kona-camera-sensor-rb5.dtsi"
#include "kona-rb5-audio-overlay.dtsi"
#include "kona-thermal-overlay.dtsi"

&qupv3_se12_2uart {
	status = "ok";
};

&pm8150a_amoled {
	status = "ok";
};

&pcie1 {
	status = "ok";
	qcom,boot-option = <0x0>;
	qcom,core-preset = <0x77777777>;
	qcom,target-link-speed = <2>;
	qcom,ep-gpio = <&tlmm 1 0>;
	pinctrl-0 = <&pcie1_perst_default
			&pcie1_clkreq_default
			&pcie1_wake_default
			&pcie1_ep_default>;
};

&pcie1_msi {
	status = "ok";
};

&tlmm {
	pcie1_ep_default: pcie1_ep_default {
		mux {
			pins = "gpio1";
			function = "gpio";
		};

		config {
			pins = "gpio1";
			drive-strength = <16>;
			output-high;
			bias-disable;
		};
	};

	pcie1_clkreq_sleep: pcie1_clkreq_sleep {
		mux {
			pins = "gpio83";
			function = "gpio";
		};

		config {
			pins = "gpio83";
			drive-strength = <2>;
			bias-pull-up;
		};
	};
};

&pcie2_rp {
	/delete-node/ wil6210_pci;
	nvme: nvme {
		reg = <0 0 0 0 0>;
		qcom,iommu-group = <&nvme_pci_iommu_group>;
		#address-cells = <1>;
		#size-cells = <1>;
		nvme_pci_iommu_group: nvme_pci_iommu_group {
			qcom,iommu-dma-addr-pool = <0x60000000 0xa0000000>;
			qcom,iommu-dma = "atomic";
		};
	};
};

&pcie2 {
	status = "ok";
	qcom,boot-option = <0x0>;
	qcom,core-preset = <0x77777777>;
	qcom,target-link-speed = <2>;
};

&spkr_1_sd_n_sleep {
	mux {
		pins = "gpio130";
		function = "gpio";
	};

	config {
		pins = "gpio130";
		drive-strength = <2>;   /* 2 mA */
		bias-pull-down;
		input-enable;
	};
};

&spkr_1_sd_n_active {
	mux {
		pins = "gpio130";
		function = "gpio";
	};

	config {
		pins = "gpio130";
		drive-strength = <16>;   /* 16 mA */
		bias-disable;
		output-high;
	};
};

&dai_mi2s2 {
	compatible = "qcom,msm-dai-q6-mi2s";
	qcom,msm-dai-q6-mi2s-dev-id = <2>;
	qcom,msm-mi2s-rx-lines = <1>;
	qcom,msm-mi2s-tx-lines = <3>;
};

&dai_mi2s3 {
	compatible = "qcom,msm-dai-q6-mi2s";
	qcom,msm-dai-q6-mi2s-dev-id = <3>;
	qcom,msm-mi2s-rx-lines = <15>;
	qcom,msm-mi2s-tx-lines = <0>;
};

&qupv3_se6_4uart {
	status = "ok";
};

&q6core {
	cdc_tert_mi2s_gpios: msm_cdc_pinctrl_tert {
		compatible = "qcom,msm-cdc-pinctrl";
		pinctrl-names = "aud_active", "aud_sleep";
		pinctrl-0 = <&tert_mi2s_sck_active &tert_mi2s_ws_active
				&tert_mi2s_sd0_active>;
		pinctrl-1 = <&tert_mi2s_sck_sleep &tert_mi2s_ws_sleep
				&tert_mi2s_sd0_sleep>;
	};
};

&kona_snd {
	qcom,tert-mi2s-gpios = <&cdc_tert_mi2s_gpios>;
};

&qupv3_se1_i2c {
	status = "ok";
	qcom,clk-freq-out = <1000000>;
	#address-cells = <1>;
	#size-cells = <0>;
	nq@28 {
		compatible = "qcom,nq-nci";
		reg = <0x28>;
		qcom,nq-irq = <&tlmm 111 0x00>;
		qcom,nq-ven = <&tlmm 6 0x00>;
		qcom,nq-firm = <&tlmm 110 0x00>;
		qcom,nq-clkreq = <&tlmm 7 0x00>;
		interrupt-parent = <&tlmm>;
		interrupts = <111 0>;
		interrupt-names = "nfc_irq";
		pinctrl-names = "nfc_active", "nfc_suspend";
		pinctrl-0 = <&nfc_int_active &nfc_enable_active
				&nfc_clk_req_active>;
		pinctrl-1 = <&nfc_int_suspend &nfc_enable_suspend
				&nfc_clk_req_suspend>;
	};
};

&ufsphy_mem {
	compatible = "qcom,ufs-phy-qmp-v4";

	vdda-phy-supply = <&pm8150_l5>;
	vdda-phy-always-on;
	vdda-pll-supply = <&pm8150_l9>;
	vdda-phy-max-microamp = <89900>;
	vdda-pll-max-microamp = <18800>;

	status = "ok";
};

&ufshc_mem {
	vdd-hba-supply = <&ufs_phy_gdsc>;
	vdd-hba-fixed-regulator;
	vcc-supply = <&pm8150_l17>;
	vcc-voltage-level = <2504000 2950000>;
	vcc-low-voltage-sup;
	vccq-supply = <&pm8150_l6>;
	vccq2-supply = <&pm8150_s4>;
	vcc-max-microamp = <800000>;
	vccq-max-microamp = <800000>;
	vccq2-max-microamp = <800000>;

	qcom,vddp-ref-clk-supply = <&pm8150_l6>;
	qcom,vddp-ref-clk-max-microamp = <100>;
	qcom,vccq-parent-supply = <&pm8150a_s8>;
	qcom,vccq-parent-max-microamp = <210000>;

	status = "ok";
};

&soc {
	gpio_keys {
		compatible = "gpio-keys";
		label = "gpio-keys";

		pinctrl-names = "default";
		pinctrl-0 = <&key_vol_up_default>;

		vol_up {
			label = "volume_up";
			gpios = <&pm8150_gpios 6 GPIO_ACTIVE_LOW>;
			linux,input-type = <1>;
			linux,code = <KEY_VOLUMEUP>;
			gpio-key,wakeup;
			debounce-interval = <15>;
			linux,can-disable;
		};
	};

	qcom,qbt_handler {
		compatible = "qcom,qbt-handler";
		qcom,ipc-gpio = <&tlmm 23 0>;
		pinctrl-names = "default";
		pinctrl-0 = <&key_home_default>;
		qcom,finger-detect-gpio = <&pm8150_gpios 1 0>;
	};
};

&qupv3_se13_i2c {
	#address-cells = <1>;
	#size-cells = <0>;

	status = "ok";
	qcom,i2c-touch-active = "st,fts";

	st_fts@49 {
		compatible = "st,fts";
		reg = <0x49>;
		interrupt-parent = <&tlmm>;
		interrupts = <39 0x2008>;
		vdd-supply = <&pm8150a_l1>;
		avdd-supply = <&pm8150_l13>;
		pinctrl-names = "pmx_ts_active", "pmx_ts_suspend";
		pinctrl-0 = <&ts_active>;
		pinctrl-1 = <&ts_int_suspend &ts_reset_suspend>;
		st,irq-gpio = <&tlmm 39 0x2008>;
		st,reset-gpio = <&tlmm 38 0x00>;
		st,regulator_dvdd = "vdd";
		st,regulator_avdd = "avdd";
		st,x-flip = <1>;
		st,y-flip = <1>;
		panel = <&dsi_sw43404_amoled_cmd &dsi_sw43404_amoled_video
			 &dsi_sw43404_amoled_fhd_plus_cmd>;
	};
};

&vendor {
	bluetooth: bt_qca6390 {
		compatible = "qca,qca6390";
		pinctrl-names = "default";
		pinctrl-0 = <&bt_en_sleep>;
		qca,bt-reset-gpio = <&tlmm 21 0>; /* BT_EN */
		qca,wl-reset-gpio = <&tlmm 20 0>; /* WL_EN */
		qca,bt-sw-ctrl-gpio = <&tlmm 124 0>; /* SW_CTRL */
		qca,bt-vdd-aon-supply = <&pm8150_s6>;
		qca,bt-vdd-dig-supply = <&pm8009_s2>;
		qca,bt-vdd-rfa1-supply = <&pm8150_s5>;
		qca,bt-vdd-rfa2-supply = <&pm8150a_s8>;
		qca,bt-vdd-asd-supply = <&pm8150_l16>;

		qca,bt-vdd-aon-voltage-level = <950000 950000>;
		qca,bt-vdd-dig-voltage-level = <950000 952000>;
		qca,bt-vdd-rfa1-voltage-level = <1900000 1900000>;
		qca,bt-vdd-rfa2-voltage-level = <1350000 1350000>;
		qca,bt-vdd-asd-voltage-level = <3024000 3304000>;

		qca,bt-vdd-asd-current-level = <10000>;
	};

	kona_mtp_batterydata: qcom,battery-data {
		qcom,batt-id-range-pct = <15>;
		#include "fg-gen4-batterydata-alium-3600mah.dtsi"
		#include "fg-gen4-batterydata-ascent-3450mah.dtsi"
	};

	extcon_usb1: extcon_usb1 {
		compatible = "linux,extcon-usb-gpio";
		vbus-gpio = <&pm8150_gpios 10 GPIO_ACTIVE_HIGH>;
		id-gpio = <&tlmm 91 GPIO_ACTIVE_HIGH>;
		vbus-out-gpio = <&pm8150_gpios 9 GPIO_ACTIVE_HIGH>;

		pinctrl-names = "default";
		pinctrl-0 = <&usb2_vbus_det_default
			     &usb2_id_det_default
			     &usb2_vbus_boost_default>;
	};
};

&vreg_hap_boost {
	status = "ok";
};

&pm8150b_haptics {
	vdd-supply = <&vreg_hap_boost>;
};

&pm8150b_vadc {
	#address-cells = <1>;
	#size-cells = <0>;

	vph_pwr@83 {
		reg = <ADC_VPH_PWR>;
		label = "vph_pwr";
		qcom,pre-scaling = <1 3>;
	};

	conn_therm@4f {
		reg = <ADC_AMUX_THM3_PU2>;
		label = "conn_therm";
		qcom,ratiometric;
		qcom,hw-settle-time = <200>;
		qcom,pre-scaling = <1 1>;
	};

	chg_sbux@99 {
		reg = <ADC_SBUx>;
		label = "chg_sbux";
		qcom,pre-scaling = <1 3>;
	};

	mid_chg_div6@1e {
		reg = <ADC_MID_CHG_DIV6>;
		label = "chg_mid";
		qcom,pre-scaling = <1 6>;
	};

	usb_in_i_uv@7 {
		reg = <ADC_USB_IN_I>;
		label = "usb_in_i_uv";
		qcom,pre-scaling = <1 1>;
	};

	usb_in_v_div_16@8 {
		reg = <ADC_USB_IN_V_16>;
		label = "usb_in_v_div_16";
		qcom,pre-scaling = <1 16>;
	};
};

&pm8150b_charger {
	status = "ok";
	qcom,sec-charger-config = <1>;
	qcom,auto-recharge-soc = <98>;
	io-channels = <&pm8150b_vadc ADC_MID_CHG_DIV6>,
		      <&pm8150b_vadc ADC_USB_IN_I>,
		      <&pm8150b_vadc ADC_SBUx>,
		      <&pm8150b_vadc ADC_VPH_PWR>,
		      <&pm8150b_vadc ADC_CHG_TEMP>;
	io-channel-names = "mid_voltage",
			   "usb_in_current",
			   "sbux_res",
			   "vph_voltage",
			   "chg_temp";
	qcom,battery-data = <&kona_mtp_batterydata>;
	qcom,step-charging-enable;
	qcom,sw-jeita-enable;
	qcom,wd-bark-time-secs = <16>;
	qcom,suspend-input-on-debug-batt;
	qcom,fcc-stepping-enable;
	qcom,smb-internal-pull-kohm = <0>;
};

&pm8150b_fg {
	status = "ok";
	qcom,battery-data = <&kona_mtp_batterydata>;
	qcom,hold-soc-while-full;
	qcom,linearize-soc;
	qcom,five-pin-battery;
	qcom,cl-wt-enable;
	qcom,soc-scale-mode-en;
	qcom,force-calib-level = <130>;
	/* ESR fast calibration */
	qcom,fg-esr-timer-chg-fast = <0 7>;
	qcom,fg-esr-timer-dischg-fast = <0 7>;
	qcom,fg-esr-timer-chg-slow = <0 96>;
	qcom,fg-esr-timer-dischg-slow = <0 96>;
	qcom,fg-esr-cal-soc-thresh = <26 230>;
	qcom,fg-esr-cal-temp-thresh = <10 40>;
};

&qupv3_se15_i2c {
	#address-cells = <1>;
	#size-cells = <0>;
#include "smb1390.dtsi"
	redriver: redriver@1c {
	compatible = "onnn,redriver";
	reg = <0x1c>;
	extcon = <&pm8150b_pdphy>, <&pm8150b_pdphy>;
	eq = /bits/ 8 <
	    /* Parameters for USB */
	    0x4 0x4 0x4 0x4
	    /* Parameters for DP */
	    0x6 0x4 0x4 0x6>;
	flat-gain = /bits/ 8 <
	    /* Parameters for USB */
	    0x3 0x1 0x1 0x3
	    /* Parameters for DP */
	    0x2 0x1 0x1 0x2>;
	output-comp = /bits/ 8 <
	    /* Parameters for USB */
	    0x3 0x3 0x3 0x3
	    /* Parameters for DP */
	    0x3 0x3 0x3 0x3>;
	loss-match = /bits/ 8 <
	    /* Parameters for USB */
	    0x1 0x3 0x3 0x1
	    /* Parameters for DP */
	    0x3 0x3 0x3 0x3>;
	};

	fsa4480: fsa4480@43 {
	 status = "disabled";
	};

	halo,hl6111r@25 {
		compatible = "halo,hl6111r";
		reg = <0x25>;
		status = "ok";
	};
};

&smb1390 {
	pinctrl-names = "default";
	pinctrl-0 = <&smb_stat_default>;
	status = "ok";
};

&smb1390_charger {
	io-channels = <&pm8150b_vadc ADC_AMUX_THM2>;
	io-channel-names = "cp_die_temp";
	qcom,parallel-output-mode = <2>;
	qcom,min-ilim-ua = <750000>;
	status = "ok";
};

&smb1390_slave {
	status = "ok";
};

&smb1390_slave_charger {
	status = "ok";
};

&pm8150_vadc {
	#address-cells = <1>;
	#size-cells = <0>;

	vph_pwr@83 {
		reg = <ADC_VPH_PWR>;
		label = "vph_pwr";
		qcom,pre-scaling = <1 3>;
	};

	vcoin@85 {
		reg = <ADC_VCOIN>;
		label = "vcoin";
		qcom,pre-scaling = <1 3>;
	};

	xo_therm@4c {
		reg = <ADC_XO_THERM_PU2>;
		label = "xo_therm";
		qcom,ratiometric;
		qcom,hw-settle-time = <200>;
		qcom,pre-scaling = <1 1>;
	};

	skin_therm@4d {
		reg = <ADC_AMUX_THM1_PU2>;
		label = "skin_therm";
		qcom,ratiometric;
		qcom,hw-settle-time = <200>;
		qcom,pre-scaling = <1 1>;
	};

	pa_therm1@4e {
		reg = <ADC_AMUX_THM2_PU2>;
		label = "pa_therm1";
		qcom,ratiometric;
		qcom,hw-settle-time = <200>;
		qcom,pre-scaling = <1 1>;
	};
};

&pm8150l_vadc {
	#address-cells = <1>;
	#size-cells = <0>;

	vph_pwr@83 {
		reg = <ADC_VPH_PWR>;
		label = "vph_pwr";
		qcom,pre-scaling = <1 3>;
	};

	camera_flash_therm@4d {
		reg = <ADC_AMUX_THM1_PU2>;
		label = "camera_flash_therm";
		qcom,ratiometric;
		qcom,hw-settle-time = <200>;
		qcom,pre-scaling = <1 1>;
	};

	skin_msm_therm@4e {
		reg = <ADC_AMUX_THM2_PU2>;
		label = "skin_msm_therm";
		qcom,ratiometric;
		qcom,hw-settle-time = <200>;
		qcom,pre-scaling = <1 1>;
	};

	pa_therm2@4f {
		reg = <ADC_AMUX_THM3_PU2>;
		label = "pa_therm2";
		qcom,ratiometric;
		qcom,hw-settle-time = <200>;
		qcom,pre-scaling = <1 1>;
	};
};

&pm8150b_adc_tm {
	#address-cells = <1>;
	#size-cells = <0>;

	io-channels = <&pm8150b_vadc ADC_AMUX_THM3_PU2>;

	conn_therm@4f {
		reg = <ADC_AMUX_THM3_PU2>;
		qcom,ratiometric;
		qcom,hw-settle-time = <200>;
	};
};

&pm8150_adc_tm {
	#address-cells = <1>;
	#size-cells = <0>;

	io-channels = <&pm8150_vadc ADC_XO_THERM_PU2>,
			<&pm8150_vadc ADC_AMUX_THM1_PU2>,
			<&pm8150_vadc ADC_AMUX_THM2_PU2>;

	xo_therm@4c {
		reg = <ADC_XO_THERM_PU2>;
		qcom,ratiometric;
		qcom,hw-settle-time = <200>;
	};

	skin_therm@4d {
		reg = <ADC_AMUX_THM1_PU2>;
		qcom,ratiometric;
		qcom,hw-settle-time = <200>;
	};

	pa_therm1@4e {
		reg = <ADC_AMUX_THM2_PU2>;
		qcom,ratiometric;
		qcom,hw-settle-time = <200>;
	};
};

&pm8150l_adc_tm {
	#address-cells = <1>;
	#size-cells = <0>;

	camera_flash_therm@4d {
		reg = <ADC_AMUX_THM1_PU2>;
		qcom,ratiometric;
		qcom,hw-settle-time = <200>;
	};

	skin_msm_therm@4e {
		reg = <ADC_AMUX_THM2_PU2>;
		qcom,ratiometric;
		qcom,hw-settle-time = <200>;
	};

	pa_therm2@4f {
		reg = <ADC_AMUX_THM3_PU2>;
		qcom,ratiometric;
		qcom,hw-settle-time = <200>;
	};
};

&spmi_debug_bus {
	status = "ok";
};

&dsi_sw43404_amoled_cmd {
	qcom,panel-supply-entries = <&dsi_panel_pwr_supply>;
	qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
	qcom,mdss-dsi-bl-min-level = <1>;
	qcom,mdss-dsi-bl-max-level = <1023>;
	qcom,mdss-brightness-max-level = <255>;
	qcom,platform-te-gpio = <&tlmm 66 0>;
	qcom,platform-reset-gpio = <&tlmm 75 0>;
	qcom,mdss-dsi-panel-test-pin = <&tlmm 46 0>;
};

&dsi_sw43404_amoled_video {
	qcom,panel-supply-entries = <&dsi_panel_pwr_supply>;
	qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
	qcom,mdss-dsi-bl-min-level = <1>;
	qcom,mdss-dsi-bl-max-level = <1023>;
	qcom,mdss-brightness-max-level = <255>;
	qcom,platform-reset-gpio = <&tlmm 75 0>;
	qcom,mdss-dsi-panel-test-pin = <&tlmm 46 0>;
};

&dsi_sw43404_amoled_fhd_plus_cmd {
	qcom,panel-supply-entries = <&dsi_panel_pwr_supply>;
	qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
	qcom,mdss-dsi-bl-min-level = <1>;
	qcom,mdss-dsi-bl-max-level = <1023>;
	qcom,mdss-brightness-max-level = <255>;
	qcom,platform-te-gpio = <&tlmm 66 0>;
	qcom,platform-reset-gpio = <&tlmm 75 0>;
	qcom,mdss-dsi-panel-test-pin = <&tlmm 46 0>;
};

&dsi_sim_cmd {
	qcom,panel-supply-entries = <&dsi_panel_pwr_supply>;
	qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
	qcom,platform-reset-gpio = <&tlmm 75 0>;
};

&dsi_sim_vid {
	qcom,panel-supply-entries = <&dsi_panel_pwr_supply>;
	qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
	qcom,platform-reset-gpio = <&tlmm 75 0>;
};

&dsi_sim_dsc_375_cmd {
	qcom,panel-supply-entries = <&dsi_panel_pwr_supply>;
	qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
	qcom,platform-reset-gpio = <&tlmm 75 0>;
};

&dsi_sim_dsc_10b_cmd {
	qcom,panel-supply-entries = <&dsi_panel_pwr_supply>;
	qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
	qcom,platform-reset-gpio = <&tlmm 75 0>;
};

&dsi_dual_sim_cmd {
	qcom,panel-supply-entries = <&dsi_panel_pwr_supply>;
	qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
	qcom,platform-reset-gpio = <&tlmm 75 0>;
};

&dsi_dual_sim_vid {
	qcom,panel-supply-entries = <&dsi_panel_pwr_supply>;
	qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
	qcom,platform-reset-gpio = <&tlmm 75 0>;
};

&dsi_dual_sim_dsc_375_cmd {
	qcom,panel-supply-entries = <&dsi_panel_pwr_supply>;
	qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
	qcom,platform-reset-gpio = <&tlmm 75 0>;
};

&dsi_sim_sec_hd_cmd {
	qcom,panel-supply-entries = <&dsi_panel_pwr_supply>;
	qcom,panel-sec-supply-entries = <&dsi_panel_pwr_supply>;
	qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs";
	qcom,mdss-dsi-sec-bl-pmic-control-type = "bl_ctrl_dcs";
	qcom,mdss-dsi-bl-min-level = <1>;
	qcom,mdss-dsi-bl-max-level = <1023>;
	qcom,platform-reset-gpio = <&tlmm 75 0>;
	qcom,platform-sec-reset-gpio = <&tlmm 128 0>;
};

&dsi_ext_bridge_4k30p {
	qcom,dsi-ctrl-num = <0>;
	qcom,dsi-phy-num = <0>;
	qcom,dsi-select-clocks = "mux_byte_clk0", "mux_pixel_clk0";
	qcom,mdss-dsi-ext-bridge-hpd;
	qcom,mdss-dsi-ext-bridge-custom-topology;
};

&sde_dsi {
	qcom,dsi-default-panel = <&dsi_ext_bridge_4k30p>;
	boot-panel-param = "disabled";

	ports {
		#address-cells = <1>;
		#size-cells = <0>;

		port@0 {
			reg = <0>;
			ext_dsi_out: endpoint {
				remote-endpoint = <&lt9611_in>;
			};
		};
	};
};

&thermal_zones {
	conn-therm-usr {
		polling-delay-passive = <0>;
		polling-delay = <0>;
		thermal-governor = "user_space";
		thermal-sensors = <&pm8150b_adc_tm ADC_AMUX_THM3_PU2>;
		wake-capable-sensor;
		trips {
			active-config0 {
				temperature = <125000>;
				hysteresis = <1000>;
				type = "passive";
			};
		};
	};

	xo-therm-usr {
		polling-delay-passive = <0>;
		polling-delay = <0>;
		thermal-governor = "user_space";
		thermal-sensors = <&pm8150_adc_tm ADC_XO_THERM_PU2>;
		wake-capable-sensor;
		trips {
			active-config0 {
				temperature = <125000>;
				hysteresis = <1000>;
				type = "passive";
			};
		};
	};

	skin-therm-usr {
		polling-delay-passive = <0>;
		polling-delay = <0>;
		thermal-governor = "user_space";
		thermal-sensors = <&pm8150_adc_tm ADC_AMUX_THM1_PU2>;
		wake-capable-sensor;
		trips {
			active-config0 {
				temperature = <125000>;
				hysteresis = <1000>;
				type = "passive";
			};
		};
	};

	mmw-pa1-usr {
		polling-delay-passive = <0>;
		polling-delay = <0>;
		thermal-governor = "user_space";
		thermal-sensors = <&pm8150_adc_tm ADC_AMUX_THM2_PU2>;
		wake-capable-sensor;
		trips {
			active-config0 {
				temperature = <125000>;
				hysteresis = <1000>;
				type = "passive";
			};
		};
	};

	camera-therm-usr {
		polling-delay-passive = <0>;
		polling-delay = <0>;
		thermal-governor = "user_space";
		thermal-sensors = <&pm8150l_adc_tm ADC_AMUX_THM1_PU2>;
		wake-capable-sensor;
		trips {
			active-config0 {
				temperature = <125000>;
				hysteresis = <1000>;
				type = "passive";
			};
		};
	};

	skin-msm-therm-usr {
		polling-delay-passive = <0>;
		polling-delay = <0>;
		thermal-governor = "user_space";
		thermal-sensors = <&pm8150l_adc_tm ADC_AMUX_THM2_PU2>;
		wake-capable-sensor;
		trips {
			active-config0 {
				temperature = <125000>;
				hysteresis = <1000>;
				type = "passive";
			};
		};
	};

	mmw-pa2-usr {
		polling-delay-passive = <0>;
		polling-delay = <0>;
		thermal-governor = "user_space";
		thermal-sensors = <&pm8150l_adc_tm ADC_AMUX_THM3_PU2>;
		wake-capable-sensor;
		trips {
			active-config0 {
				temperature = <125000>;
				hysteresis = <1000>;
				type = "passive";
			};
		};
	};
};

&sdhc_2 {
	vdd-supply = <&pm8150a_l9>;
	qcom,vdd-voltage-level = <2950000 2960000>;
	qcom,vdd-current-level = <200 800000>;

	vdd-io-supply = <&pm8150a_l6>;
	qcom,vdd-io-voltage-level = <1808000 2960000>;
	qcom,vdd-io-current-level = <200 22000>;

	pinctrl-names = "active", "sleep";
	pinctrl-0 = <&sdc2_clk_on  &sdc2_cmd_on &sdc2_data_on &storage_cd>;
	pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &storage_cd>;

	cd-gpios = <&tlmm 77 GPIO_ACTIVE_LOW>;

	status = "ok";
};

&usb1 {
	dwc1: dwc3@a800000 {
		dr_mode = "host";
	};
};

&wil6210 {
	status = "ok";
};

&q6core {
};

&sde_dp {
	qcom,dp-aux-switch = <&redriver>;
	qcom,aux-en-gpio = <&tlmm 69 0>;
	qcom,aux-sel-gpio = <&tlmm 71 0>;
};

&qupv3_se5_i2c {
	status = "okay";
	qcom,clk-freq-out = <400000>;
	lt9611: lt,lt9611@2b {
		compatible = "lt,lt9611uxc";
		reg = <0x2b>;
		interrupt-parent = <&tlmm>;
		interrupts = <63 0>;
		interrupt-names = "lt_irq";
		lt,irq-gpio = <&tlmm 63 0x0>;
		lt,reset-gpio = <&pm8150l_gpios 5 0>;
		instance_id = <0>;

		pinctrl-names = "default";
		pinctrl-0 = <&lt9611_pins &lt9611_rst_default>;

		lt,preferred-mode = "3840x2160";

		lt,audio-support;
		lt,ext-disp = <&ext_disp>;

		lt,customize-modes {
			lt,customize-mode-id@0 {
				lt,mode-h-active = <1920>;
				lt,mode-h-front-porch = <88>;
				lt,mode-h-pulse-width = <44>;
				lt,mode-h-back-porch = <148>;
				lt,mode-h-active-high;
				lt,mode-v-active = <1080>;
				lt,mode-v-front-porch = <4>;
				lt,mode-v-pulse-width = <5>;
				lt,mode-v-back-porch = <36>;
				lt,mode-v-active-high;
				lt,mode-refresh-rate = <60>;
				lt,mode-clock-in-khz = <148500>;
			};
			lt,customize-mode-id@1 {
				lt,mode-h-active = <3840>;
				lt,mode-h-front-porch = <176>;
				lt,mode-h-pulse-width = <88>;
				lt,mode-h-back-porch = <296>;
				lt,mode-h-active-high;
				lt,mode-v-active = <2160>;
				lt,mode-v-front-porch = <8>;
				lt,mode-v-pulse-width = <10>;
				lt,mode-v-back-porch = <72>;
				lt,mode-v-active-high;
				lt,mode-refresh-rate = <30>;
				lt,mode-clock-in-khz = <297000>;
			};


			lt,customize-mode-id@2 {
				lt,mode-h-active = <1280>;
				lt,mode-h-front-porch = <110>;
				lt,mode-h-pulse-width = <40>;
				lt,mode-h-back-porch = <220>;
				lt,mode-h-active-high;
				lt,mode-v-active = <720>;
				lt,mode-v-front-porch = <5>;
				lt,mode-v-pulse-width = <5>;
				lt,mode-v-back-porch = <20>;
				lt,mode-v-active-high;
				lt,mode-refresh-rate = <60>;
				lt,mode-clock-in-khz = <74250>;
			};


			lt,customize-mode-id@3 {
				lt,mode-h-active = <720>;
				lt,mode-h-front-porch = <16>;
				lt,mode-h-pulse-width = <62>;
				lt,mode-h-back-porch = <60>;
				lt,mode-v-active = <480>;
				lt,mode-v-front-porch = <9>;
				lt,mode-v-pulse-width = <6>;
				lt,mode-v-back-porch = <30>;
				lt,mode-refresh-rate = <60>;
				lt,mode-clock-in-khz = <27000>;
			};
		};

		ports {
			#address-cells = <1>;
			#size-cells = <0>;

			port@0 {
				reg = <0>;
				lt9611_in: endpoint {
					remote-endpoint = <&ext_dsi_out>;
				};
			};
		};
	};
};

&pm8150a_l11 {
	qcom,init-voltage = <3304000>;
	regulator-always-on;
};

&pm8150l_gpios {
	lt9611_rst {
		lt9611_rst_default: lt9611_rst_default {
			pins = "gpio5";
			function = "normal";
			output-enable;
			bias-pull-down;
			power-source = <0>;
		};
	};
};

&lt9611_pins {
	mux {
		pins = "gpio63";
		function = "gpio";
	};

	config {
		pins = "gpio63";
		drive-strength = <8>;
		bias-disable = <0>;
	};
};

&soc {
	 clk40M: can_clock {
		compatible = "fixed-clock";
		#clock-cells = <0>;
		clock-frequency = <40000000>;
	};
};

&qupv3_se0_spi {
	status = "okay";
	can@0 {
		compatible = "microchip,mcp2517fd";
		reg = <0>;
		clocks = <&clk40M>;
		interrupt-parent = <&tlmm>;
		interrupts = <15 0>;
		interrupt-names = "can_irq";
		spi-max-frequency = <10000000>;
		gpio-controller;
		status = "okay";
	};
};