monit.md

Install Monit

On Ubuntu 16.04, 14.04

apt-get install monit

Monit Configuration

your /etc/monit/monitrc should look like the file monitrc above.

Restart Monit

service monit restart

Monit Status

Get status for all services you are monitoring with command monit status

monitor-worker.sh

#!/bin/bash

supervisorctl status | grep worker | grep 'RUNNING   pid'
if [ $? -ne 0 ]; then
	exit 1;
fi
exit 0;

monitrc

###############################################################################
## Monit control file
###############################################################################
##
## Comments begin with a '#' and extend through the end of the line. Keywords
## are case insensitive. All path's MUST BE FULLY QUALIFIED, starting with '/'.
##
## Below you will find examples of some frequently used statements. For 
## information about the control file and a complete list of statements and 
## options, please have a look in the Monit manual.
##
##
###############################################################################
## Global section
###############################################################################
##
## Start Monit in the background (run as a daemon):
#
  set daemon 120            # check services at 2-minute intervals
#   with start delay 240    # optional: delay the first check by 4-minutes (by 
#                           # default Monit check immediately after Monit start)
#
#
## Set syslog logging. If you want to log to a standalone log file instead,
## specify the full path to the log file
#
  set logfile /var/log/monit.log
#
#
## Set the location of the Monit lock file which stores the process id of the
## running Monit instance. By default this file is stored in $HOME/.monit.pid
#
# set pidfile /var/run/monit.pid
#
## Set the location of the Monit id file which stores the unique id for the
## Monit instance. The id is generated and stored on first Monit start. By 
## default the file is placed in $HOME/.monit.id.
#
# set idfile /var/.monit.id
  set idfile /var/lib/monit/id
#
## Set the location of the Monit state file which saves monitoring states
## on each cycle. By default the file is placed in $HOME/.monit.state. If
## the state file is stored on a persistent filesystem, Monit will recover
## the monitoring state across reboots. If it is on temporary filesystem, the
## state will be lost on reboot which may be convenient in some situations.
#
  set statefile /var/lib/monit/state
#
#

## Set limits for various tests. The following example shows the default values:
##
# set limits {
#     programOutput:     512 B,    # check program's output truncate limit
#     sendExpectBuffer:  256 B,    # limit for send/expect protocol test
#     fileContentBuffer: 512 B,    # limit for file content test
#     httpContentBuffer: 1 MB,     # limit for HTTP content test
#     networkTimeout:    5 seconds # timeout for network I/O
# }

## Set global SSL options (just most common options showed, see manual for
## full list).
#
# set ssl {
#     verify     : enable, # verify SSL certificates (disabled by default but STRONGLY RECOMMENDED)
#     selfsigned : allow   # allow self signed SSL certificates (reject by default)
# }
#
#
## Set the list of mail servers for alert delivery. Multiple servers may be 
## specified using a comma separator. If the first mail server fails, Monit 
# will use the second mail server in the list and so on. By default Monit uses 
# port 25 - it is possible to override this with the PORT option.
#
# set mailserver mail.bar.baz,               # primary mailserver
#                backup.bar.baz port 10025,  # backup mailserver on port 10025
#                localhost                   # fallback relay
 set mailserver localhost
#
## By default Monit will drop alert events if no mail servers are available. 
## If you want to keep the alerts for later delivery retry, you can use the 
## EVENTQUEUE statement. The base directory where undelivered alerts will be 
## stored is specified by the BASEDIR option. You can limit the queue size 
## by using the SLOTS option (if omitted, the queue is limited by space
## available in the back end filesystem).
#
  set eventqueue
      basedir /var/lib/monit/events # set the base directory where events will be stored
      slots 100                     # optionally limit the queue size
#
#
## Send status and events to M/Monit (for more informations about M/Monit 
## see http://mmonit.com/). By default Monit registers credentials with 
## M/Monit so M/Monit can smoothly communicate back to Monit and you don't
## have to register Monit credentials manually in M/Monit. It is possible to
## disable credential registration using the commented out option below. 
## Though, if safety is a concern we recommend instead using https when
## communicating with M/Monit and send credentials encrypted.
#
# set mmonit http://monit:monit@192.168.1.10:8080/collector
#     # and register without credentials     # Don't register credentials
#
#
## Monit by default uses the following format for alerts if the the mail-format
## statement is missing::
## --8<--
## set mail-format {
##   from:    monit@$HOST
##   subject: monit alert --  $EVENT $SERVICE
##   message: $EVENT Service $SERVICE
##                 Date:        $DATE
##                 Action:      $ACTION
##                 Host:        $HOST
##                 Description: $DESCRIPTION
##
##            Your faithful employee,
##            Monit
## }
## --8<--
##
## You can override this message format or parts of it, such as subject
## or sender using the MAIL-FORMAT statement. Macros such as $DATE, etc.
## are expanded at runtime. For example, to override the sender, use:
#
# set mail-format { from: monit@foo.bar }
#
#
## You can set alert recipients whom will receive alerts if/when a 
## service defined in this file has errors. Alerts may be restricted on 
## events by using a filter as in the second example below.
#
 set alert yourmail@domain.com                       # receive all alerts
#
## Do not alert when Monit starts, stops or performs a user initiated action.
## This filter is recommended to avoid getting alerts for trivial cases.
#
 set alert yourmail@domain.com not on { instance, action }
#
#
## Monit has an embedded HTTP interface which can be used to view status of 
## services monitored and manage services from a web interface. The HTTP 
## interface is also required if you want to issue Monit commands from the
## command line, such as 'monit status' or 'monit restart service' The reason
## for this is that the Monit client uses the HTTP interface to send these
## commands to a running Monit daemon. See the Monit Wiki if you want to 
## enable SSL for the HTTP interface. 
#
 set httpd port 2812 and
     use address localhost  # only accept connection from localhost
     allow localhost        # allow localhost to connect to the server and
     allow admin:biAyMiAxMzo      # require user 'admin' with password 'monit'
#
###############################################################################
## Services
###############################################################################
##
## Check general system resources such as load average, cpu and memory
## usage. Each test specifies a resource, conditions and the action to be
## performed should a test fail.
#
#  check system $HOST
#    if loadavg (1min) > 4 then alert
#    if loadavg (5min) > 2 then alert
#    if cpu usage > 95% for 10 cycles then alert
#    if memory usage > 75% then alert
#    if swap usage > 25% then alert
#
#    
## Check if a file exists, checksum, permissions, uid and gid. In addition
## to alert recipients in the global section, customized alert can be sent to 
## additional recipients by specifying a local alert handler. The service may 
## be grouped using the GROUP option. More than one group can be specified by
## repeating the 'group name' statement.
#    
#  check file apache_bin with path /usr/local/apache/bin/httpd
#    if failed checksum and 
#       expect the sum 8f7f419955cefa0b33a2ba316cba3659 then unmonitor
#    if failed permission 755 then unmonitor
#    if failed uid root then unmonitor
#    if failed gid root then unmonitor
#    alert security@foo.bar on {
#           checksum, permission, uid, gid, unmonitor
#        } with the mail-format { subject: Alarm! }
#    group server
#
#    
## Check that a process is running, in this case Apache, and that it respond
## to HTTP and HTTPS requests. Check its resource usage such as cpu and memory,
## and number of children. If the process is not running, Monit will restart 
## it by default. In case the service is restarted very often and the 
## problem remains, it is possible to disable monitoring using the TIMEOUT
## statement. This service depends on another service (apache_bin) which
## is defined above.
#    
#  check process apache with pidfile /usr/local/apache/logs/httpd.pid
#    start program = "/etc/init.d/httpd start" with timeout 60 seconds
#    stop program  = "/etc/init.d/httpd stop"
#    if cpu > 60% for 2 cycles then alert
#    if cpu > 80% for 5 cycles then restart
#    if totalmem > 200.0 MB for 5 cycles then restart
#    if children > 250 then restart
#    if loadavg(5min) greater than 10 for 8 cycles then stop
#    if failed host www.tildeslash.com port 80 protocol http 
#       and request "/somefile.html"
#    then restart
#    if failed port 443 protocol https with timeout 15 seconds then restart
#    if 3 restarts within 5 cycles then unmonitor
#    depends on apache_bin
#    group server
#    
#    
## Check filesystem permissions, uid, gid, space and inode usage. Other services,
## such as databases, may depend on this resource and an automatically graceful
## stop may be cascaded to them before the filesystem will become full and data
## lost.
#
#  check filesystem datafs with path /dev/sdb1
#    start program  = "/bin/mount /data"
#    stop program  = "/bin/umount /data"
#    if failed permission 660 then unmonitor
#    if failed uid root then unmonitor
#    if failed gid disk then unmonitor
#    if space usage > 80% for 5 times within 15 cycles then alert
#    if space usage > 99% then stop
#    if inode usage > 30000 then alert
#    if inode usage > 99% then stop
#    group server
#
#
## Check a file's timestamp. In this example, we test if a file is older 
## than 15 minutes and assume something is wrong if its not updated. Also,
## if the file size exceed a given limit, execute a script
#
#  check file database with path /data/mydatabase.db
#    if failed permission 700 then alert
#    if failed uid data then alert
#    if failed gid data then alert
#    if timestamp > 15 minutes then alert
#    if size > 100 MB then exec "/my/cleanup/script" as uid dba and gid dba
#
#
## Check directory permission, uid and gid.  An event is triggered if the 
## directory does not belong to the user with uid 0 and gid 0.  In addition, 
## the permissions have to match the octal description of 755 (see chmod(1)).
#
#  check directory bin with path /bin
#    if failed permission 755 then unmonitor
#    if failed uid 0 then unmonitor
#    if failed gid 0 then unmonitor
#
#
## Check a remote host availability by issuing a ping test and check the 
## content of a response from a web server. Up to three pings are sent and 
## connection to a port and an application level network check is performed.
#
#  check host myserver with address 192.168.1.1
#    if failed ping then alert
#    if failed port 3306 protocol mysql with timeout 15 seconds then alert
#    if failed port 80 protocol http
#       and request /some/path with content = "a string"
#    then alert
#
#
## Check a network link status (up/down), link capacity changes, saturation
## and bandwidth usage.
#
#  check network public with interface eth0
#    if failed link then alert
#    if changed link then alert
#    if saturation > 90% then alert
#    if download > 10 MB/s then alert
#    if total upload > 1 GB in last hour then alert
#
#
## Check custom program status output.
#
#  check program myscript with path /usr/local/bin/myscript.sh
#    if status != 0 then alert
#
#

#MySQL Monitoring
check process mysqld with pidfile "/var/run/mysqld/mysqld.pid"				
	if cpu > 80% for 2 cycles then alert

#PHP-FPM
check process php7.0-fpm with pidfile "/var/run/php/php7.0-fpm.pid"
	if cpu > 80% for 2 cycles then alert

#Nginx
check process nginx with pidfile "/var/run/nginx.pid"
	if cpu > 80% for 2 cycles then alert

#System Monitoring 
check system $HOST
	if memory usage > 80% for 2 cycles then alert
	if cpu usage (user) > 70% for 2 cycles then alert
        if cpu usage (system) > 30% then alert
 	if cpu usage (wait) > 20% then alert
	if loadavg (1min) > 6 for 2 cycles then alert 
	if loadavg (5min) > 4 for 2 cycles then alert
	if swap usage > 5% then alert

check filesystem rootfs with path /
       if space usage > 80% then alert

check program worker with path /usr/local/bin/monitor-worker.sh
       if status != 0 then alert

###############################################################################
## Includes
###############################################################################
##
## It is possible to include additional configuration parts from other files or
## directories.
#
#   include /etc/monit/conf.d/*
#   include /etc/monit/conf-enabled/*
#