Last active
December 23, 2018 19:27
-
-
Save Mambix/25f093f7dc8221e9b26191933d0b7e7a to your computer and use it in GitHub Desktop.
Slic3r settings
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| *.exe | |
| lib/ | |
| res/ | |
| cpfworkrt/ |
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| # generated by Slic3r 1.3.0-dev on | |
| adaptive_slicing = 0 | |
| adaptive_slicing_quality = 75% | |
| avoid_crossing_perimeters = 0 | |
| bed_shape = 0x0,200x0,200x200,0x200 | |
| bed_temperature = 60 | |
| before_layer_gcode = | |
| between_objects_gcode = | |
| bottom_infill_pattern = rectilinear | |
| bottom_solid_layers = 3 | |
| bridge_acceleration = 0 | |
| bridge_fan_speed = 100 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_connections_width = 0 | |
| brim_width = 5 | |
| compatible_printers = | |
| complete_objects = 0 | |
| cooling = 1 | |
| default_acceleration = 0 | |
| disable_fan_first_layers = 3 | |
| dont_support_bridges = 1 | |
| duplicate_distance = 6 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n | |
| external_perimeter_extrusion_width = 0 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extruder_offset = 0x0 | |
| extrusion_axis = E | |
| extrusion_multiplier = 1 | |
| extrusion_width = 0 | |
| fan_always_on = 0 | |
| fan_below_layer_time = 60 | |
| filament_colour = #FFFF00 | |
| filament_cost = 0 | |
| filament_density = 0 | |
| filament_diameter = 1.75 | |
| filament_max_volumetric_speed = 0 | |
| filament_notes = "" | |
| filament_settings_id = | |
| fill_angle = 45 | |
| fill_density = 30% | |
| fill_gaps = 1 | |
| fill_pattern = cubic | |
| first_layer_acceleration = 0 | |
| first_layer_bed_temperature = 65 | |
| first_layer_extrusion_width = 200% | |
| first_layer_height = 0.5 | |
| first_layer_speed = 30 | |
| first_layer_temperature = 215 | |
| gap_fill_speed = 20 | |
| gcode_arcs = 0 | |
| gcode_comments = 0 | |
| gcode_flavor = reprap | |
| has_heatbed = 1 | |
| host_type = octoprint | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 15% | |
| infill_speed = 80 | |
| interface_shells = 0 | |
| interior_brim_width = 0 | |
| layer_gcode = | |
| layer_height = 0.333 | |
| match_horizontal_surfaces = 0 | |
| max_fan_speed = 100 | |
| max_layer_height = 0.3 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_fan_speed = 35 | |
| min_layer_height = 0.15 | |
| min_print_speed = 10 | |
| min_skirt_length = 0 | |
| notes = | |
| nozzle_diameter = 0.6 | |
| octoprint_apikey = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0 | |
| perimeter_speed = 60 | |
| perimeters = 3 | |
| post_process = | |
| pressure_advance = 0 | |
| print_host = | |
| print_settings_id = | |
| printer_notes = | |
| printer_settings_id = | |
| raft_layers = 0 | |
| regions_overlap = 0 | |
| resolution = 0 | |
| retract_before_travel = 2 | |
| retract_layer_change = 0 | |
| retract_length = 2 | |
| retract_length_toolchange = 10 | |
| retract_lift = 0 | |
| retract_lift_above = 0 | |
| retract_lift_below = 0 | |
| retract_restart_extra = 0 | |
| retract_restart_extra_toolchange = 0 | |
| retract_speed = 40 | |
| seam_position = aligned | |
| sequential_print_priority = 0 | |
| serial_port = | |
| serial_speed = 250000 | |
| shortcuts = support_material | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| slowdown_below_layer_time = 5 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0 | |
| solid_infill_speed = 20 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| start_filament_gcode = "; Filament gcode\n" | |
| start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n | |
| support_material = 1 | |
| support_material_angle = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_extrusion_width = 0 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = pillars | |
| support_material_spacing = 2.5 | |
| support_material_speed = 60 | |
| support_material_threshold = 60% | |
| temperature = 210 | |
| thin_walls = 1 | |
| threads = 8 | |
| toolchange_gcode = | |
| top_infill_extrusion_width = 0 | |
| top_infill_pattern = rectilinear | |
| top_solid_infill_speed = 15 | |
| top_solid_layers = 3 | |
| travel_speed = 130 | |
| use_firmware_retraction = 0 | |
| use_relative_e_distances = 0 | |
| use_volumetric_e = 0 | |
| vibration_limit = 0 | |
| wipe = 0 | |
| xy_size_compensation = 0 | |
| z_offset = 0 | |
| z_steps_per_mm = 0 |
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| # generated by Slic3r 1.3.0-dev on Sun Dec 23 20:26:07 2018 | |
| [filament:ABS (Unknown)] | |
| bed_temperature = 105 | |
| bridge_fan_speed = 100 | |
| compatible_printers = | |
| cooling = 1 | |
| disable_fan_first_layers = 3 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 1 | |
| fan_always_on = 0 | |
| fan_below_layer_time = 60 | |
| filament_colour = #000000 | |
| filament_cost = 0 | |
| filament_density = 0 | |
| filament_diameter = 1.75 | |
| filament_max_volumetric_speed = 0 | |
| filament_notes = "" | |
| filament_settings_id = | |
| first_layer_bed_temperature = 105 | |
| first_layer_temperature = 255 | |
| max_fan_speed = 100 | |
| min_fan_speed = 35 | |
| min_print_speed = 10 | |
| slowdown_below_layer_time = 5 | |
| start_filament_gcode = "; Filament gcode\n" | |
| temperature = 255 | |
| [filament:ABS (Van Gogh)] | |
| bed_temperature = 105 | |
| bridge_fan_speed = 100 | |
| compatible_printers = | |
| cooling = 1 | |
| disable_fan_first_layers = 3 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 1 | |
| fan_always_on = 0 | |
| fan_below_layer_time = 60 | |
| filament_colour = #FFFFFF | |
| filament_cost = 0 | |
| filament_density = 0 | |
| filament_diameter = 1.75 | |
| filament_max_volumetric_speed = 0 | |
| filament_notes = "" | |
| filament_settings_id = | |
| first_layer_bed_temperature = 105 | |
| first_layer_temperature = 255 | |
| max_fan_speed = 100 | |
| min_fan_speed = 35 | |
| min_print_speed = 10 | |
| slowdown_below_layer_time = 5 | |
| start_filament_gcode = "; Filament gcode\n" | |
| temperature = 255 | |
| [filament:PLA (Anet3D)] | |
| bed_temperature = 60 | |
| bridge_fan_speed = 100 | |
| compatible_printers = | |
| cooling = 1 | |
| disable_fan_first_layers = 3 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 1 | |
| fan_always_on = 0 | |
| fan_below_layer_time = 60 | |
| filament_colour = #FFFF00 | |
| filament_cost = 0 | |
| filament_density = 0 | |
| filament_diameter = 1.75 | |
| filament_max_volumetric_speed = 0 | |
| filament_notes = "" | |
| filament_settings_id = | |
| first_layer_bed_temperature = 65 | |
| first_layer_temperature = 215 | |
| max_fan_speed = 100 | |
| min_fan_speed = 35 | |
| min_print_speed = 10 | |
| slowdown_below_layer_time = 5 | |
| start_filament_gcode = "; Filament gcode\n" | |
| temperature = 210 | |
| [filament:PLA (Transparent)] | |
| bed_temperature = 60 | |
| bridge_fan_speed = 100 | |
| compatible_printers = | |
| cooling = 1 | |
| disable_fan_first_layers = 3 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 1 | |
| fan_always_on = 0 | |
| fan_below_layer_time = 60 | |
| filament_colour = #FFFFFF | |
| filament_cost = 0 | |
| filament_density = 0 | |
| filament_diameter = 1.75 | |
| filament_max_volumetric_speed = 0 | |
| filament_notes = "" | |
| filament_settings_id = | |
| first_layer_bed_temperature = 65 | |
| first_layer_temperature = 225 | |
| max_fan_speed = 100 | |
| min_fan_speed = 35 | |
| min_print_speed = 10 | |
| slowdown_below_layer_time = 5 | |
| start_filament_gcode = "; Filament gcode\n" | |
| temperature = 220 | |
| [filament:Simple Mode] | |
| bed_temperature = 60 | |
| bridge_fan_speed = 100 | |
| compatible_printers = | |
| cooling = 1 | |
| disable_fan_first_layers = 3 | |
| end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n" | |
| extrusion_multiplier = 1 | |
| fan_always_on = 0 | |
| fan_below_layer_time = 60 | |
| filament_colour = #FFFFFF | |
| filament_cost = 0 | |
| filament_density = 0 | |
| filament_diameter = 1.75 | |
| filament_max_volumetric_speed = 0 | |
| filament_notes = "" | |
| filament_settings_id = | |
| first_layer_bed_temperature = 65 | |
| first_layer_temperature = 210 | |
| max_fan_speed = 100 | |
| min_fan_speed = 35 | |
| min_print_speed = 10 | |
| slowdown_below_layer_time = 5 | |
| start_filament_gcode = "; Filament gcode\n" | |
| temperature = 210 | |
| [presets] | |
| filament = PLA (Anet3D) | |
| filament_1 = PLA (Transparent) | |
| filament_2 = PLA (Transparent) | |
| print = Prusa i3 (0.33, 5mm) | |
| printer = Prusa i3 (0.6) | |
| [print:Prusa i3 (0.1,15mm)] | |
| adaptive_slicing = 0 | |
| adaptive_slicing_quality = 75% | |
| avoid_crossing_perimeters = 0 | |
| bottom_infill_pattern = rectilinear | |
| bottom_solid_layers = 3 | |
| bridge_acceleration = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_connections_width = 0 | |
| brim_width = 10 | |
| compatible_printers = | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| external_perimeter_extrusion_width = 0 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0 | |
| fill_angle = 45 | |
| fill_density = 10% | |
| fill_gaps = 1 | |
| fill_pattern = honeycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 200% | |
| first_layer_height = 0.2 | |
| first_layer_speed = 30 | |
| gap_fill_speed = 20 | |
| gcode_comments = 0 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 15% | |
| infill_speed = 80 | |
| interface_shells = 0 | |
| interior_brim_width = 0 | |
| layer_height = 0.1 | |
| match_horizontal_surfaces = 0 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0 | |
| perimeter_speed = 60 | |
| perimeters = 4 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| regions_overlap = 0 | |
| resolution = 0 | |
| seam_position = aligned | |
| shortcuts = support_material | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0 | |
| solid_infill_speed = 20 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_extrusion_width = 0 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = pillars | |
| support_material_spacing = 2.5 | |
| support_material_speed = 60 | |
| support_material_threshold = 60% | |
| thin_walls = 1 | |
| top_infill_extrusion_width = 0 | |
| top_infill_pattern = rectilinear | |
| top_solid_infill_speed = 15 | |
| top_solid_layers = 4 | |
| travel_speed = 130 | |
| xy_size_compensation = 0 | |
| [print:Prusa i3 (0.2,10mm)] | |
| adaptive_slicing = 0 | |
| adaptive_slicing_quality = 75% | |
| avoid_crossing_perimeters = 0 | |
| bottom_infill_pattern = rectilinear | |
| bottom_solid_layers = 3 | |
| bridge_acceleration = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_connections_width = 0 | |
| brim_width = 10 | |
| compatible_printers = | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| external_perimeter_extrusion_width = 0 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0 | |
| fill_angle = 45 | |
| fill_density = 10% | |
| fill_gaps = 1 | |
| fill_pattern = honeycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 200% | |
| first_layer_height = 0.3 | |
| first_layer_speed = 30 | |
| gap_fill_speed = 20 | |
| gcode_comments = 0 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 15% | |
| infill_speed = 80 | |
| interface_shells = 0 | |
| interior_brim_width = 0 | |
| layer_height = 0.2 | |
| match_horizontal_surfaces = 0 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0 | |
| perimeter_speed = 60 | |
| perimeters = 4 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| regions_overlap = 0 | |
| resolution = 0 | |
| seam_position = aligned | |
| shortcuts = support_material | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0 | |
| solid_infill_speed = 20 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_extrusion_width = 0 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = pillars | |
| support_material_spacing = 2.5 | |
| support_material_speed = 60 | |
| support_material_threshold = 60% | |
| thin_walls = 1 | |
| top_infill_extrusion_width = 0 | |
| top_infill_pattern = rectilinear | |
| top_solid_infill_speed = 15 | |
| top_solid_layers = 4 | |
| travel_speed = 130 | |
| xy_size_compensation = 0 | |
| [print:Prusa i3 (0.2,15mm)] | |
| adaptive_slicing = 0 | |
| adaptive_slicing_quality = 75% | |
| avoid_crossing_perimeters = 0 | |
| bottom_infill_pattern = rectilinear | |
| bottom_solid_layers = 3 | |
| bridge_acceleration = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_connections_width = 0 | |
| brim_width = 15 | |
| compatible_printers = | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| external_perimeter_extrusion_width = 0 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0 | |
| fill_angle = 45 | |
| fill_density = 15% | |
| fill_gaps = 1 | |
| fill_pattern = honeycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 200% | |
| first_layer_height = 0.3 | |
| first_layer_speed = 30 | |
| gap_fill_speed = 20 | |
| gcode_comments = 0 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 15% | |
| infill_speed = 80 | |
| interface_shells = 0 | |
| interior_brim_width = 0 | |
| layer_height = 0.2 | |
| match_horizontal_surfaces = 0 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0 | |
| perimeter_speed = 60 | |
| perimeters = 3 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| regions_overlap = 0 | |
| resolution = 0 | |
| seam_position = aligned | |
| shortcuts = support_material | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0 | |
| solid_infill_speed = 20 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 1 | |
| support_material_angle = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_extrusion_width = 0 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = pillars | |
| support_material_spacing = 2.5 | |
| support_material_speed = 60 | |
| support_material_threshold = 60% | |
| thin_walls = 1 | |
| top_infill_extrusion_width = 0 | |
| top_infill_pattern = rectilinear | |
| top_solid_infill_speed = 15 | |
| top_solid_layers = 3 | |
| travel_speed = 130 | |
| xy_size_compensation = 0 | |
| [print:Prusa i3 (0.2,5mm)] | |
| adaptive_slicing = 0 | |
| adaptive_slicing_quality = 75% | |
| avoid_crossing_perimeters = 0 | |
| bottom_infill_pattern = rectilinear | |
| bottom_solid_layers = 3 | |
| bridge_acceleration = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_connections_width = 0 | |
| brim_width = 5 | |
| compatible_printers = | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| external_perimeter_extrusion_width = 0 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0 | |
| fill_angle = 45 | |
| fill_density = 10% | |
| fill_gaps = 1 | |
| fill_pattern = honeycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 200% | |
| first_layer_height = 0.3 | |
| first_layer_speed = 40 | |
| gap_fill_speed = 20 | |
| gcode_comments = 0 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 15% | |
| infill_speed = 80 | |
| interface_shells = 0 | |
| interior_brim_width = 0 | |
| layer_height = 0.2 | |
| match_horizontal_surfaces = 0 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0 | |
| perimeter_speed = 80 | |
| perimeters = 3 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| regions_overlap = 0 | |
| resolution = 0 | |
| seam_position = aligned | |
| shortcuts = support_material | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0 | |
| solid_infill_speed = 20 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_extrusion_width = 0 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = pillars | |
| support_material_spacing = 2.5 | |
| support_material_speed = 60 | |
| support_material_threshold = 60% | |
| thin_walls = 1 | |
| top_infill_extrusion_width = 0 | |
| top_infill_pattern = rectilinear | |
| top_solid_infill_speed = 35 | |
| top_solid_layers = 3 | |
| travel_speed = 130 | |
| xy_size_compensation = 0 | |
| [print:Prusa i3 (0.25,15mm)] | |
| adaptive_slicing = 0 | |
| adaptive_slicing_quality = 75% | |
| avoid_crossing_perimeters = 0 | |
| bottom_infill_pattern = rectilinear | |
| bottom_solid_layers = 3 | |
| bridge_acceleration = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_connections_width = 0 | |
| brim_width = 15 | |
| compatible_printers = | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| external_perimeter_extrusion_width = 0 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0 | |
| fill_angle = 45 | |
| fill_density = 20% | |
| fill_gaps = 1 | |
| fill_pattern = honeycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 200% | |
| first_layer_height = 0.5 | |
| first_layer_speed = 30 | |
| gap_fill_speed = 20 | |
| gcode_comments = 0 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 15% | |
| infill_speed = 80 | |
| interface_shells = 0 | |
| interior_brim_width = 0 | |
| layer_height = 0.25 | |
| match_horizontal_surfaces = 0 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0 | |
| perimeter_speed = 60 | |
| perimeters = 3 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| regions_overlap = 0 | |
| resolution = 0 | |
| seam_position = aligned | |
| shortcuts = support_material | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0 | |
| solid_infill_speed = 20 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 1 | |
| support_material_angle = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_extrusion_width = 0 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = pillars | |
| support_material_spacing = 2.5 | |
| support_material_speed = 60 | |
| support_material_threshold = 60% | |
| thin_walls = 1 | |
| top_infill_extrusion_width = 0 | |
| top_infill_pattern = rectilinear | |
| top_solid_infill_speed = 15 | |
| top_solid_layers = 3 | |
| travel_speed = 130 | |
| xy_size_compensation = 0 | |
| [print:Prusa i3 (0.33, 5mm)] | |
| adaptive_slicing = 0 | |
| adaptive_slicing_quality = 75% | |
| avoid_crossing_perimeters = 0 | |
| bottom_infill_pattern = rectilinear | |
| bottom_solid_layers = 3 | |
| bridge_acceleration = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_connections_width = 0 | |
| brim_width = 5 | |
| compatible_printers = | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| external_perimeter_extrusion_width = 0 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0 | |
| fill_angle = 45 | |
| fill_density = 20% | |
| fill_gaps = 1 | |
| fill_pattern = cubic | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 200% | |
| first_layer_height = 0.5 | |
| first_layer_speed = 30 | |
| gap_fill_speed = 20 | |
| gcode_comments = 0 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 15% | |
| infill_speed = 80 | |
| interface_shells = 0 | |
| interior_brim_width = 0 | |
| layer_height = 0.333 | |
| match_horizontal_surfaces = 0 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0 | |
| perimeter_speed = 60 | |
| perimeters = 3 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| regions_overlap = 0 | |
| resolution = 0 | |
| seam_position = aligned | |
| shortcuts = support_material | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0 | |
| solid_infill_speed = 20 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 1 | |
| support_material_angle = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_extrusion_width = 0 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = pillars | |
| support_material_spacing = 2.5 | |
| support_material_speed = 60 | |
| support_material_threshold = 60% | |
| thin_walls = 1 | |
| top_infill_extrusion_width = 0 | |
| top_infill_pattern = rectilinear | |
| top_solid_infill_speed = 15 | |
| top_solid_layers = 3 | |
| travel_speed = 130 | |
| xy_size_compensation = 0 | |
| [print:Prusa i3 (0.33,15mm)] | |
| adaptive_slicing = 0 | |
| adaptive_slicing_quality = 75% | |
| avoid_crossing_perimeters = 0 | |
| bottom_infill_pattern = rectilinear | |
| bottom_solid_layers = 3 | |
| bridge_acceleration = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_connections_width = 0 | |
| brim_width = 15 | |
| compatible_printers = | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| external_perimeter_extrusion_width = 0 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0 | |
| fill_angle = 45 | |
| fill_density = 20% | |
| fill_gaps = 1 | |
| fill_pattern = honeycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 200% | |
| first_layer_height = 0.5 | |
| first_layer_speed = 30 | |
| gap_fill_speed = 20 | |
| gcode_comments = 0 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 15% | |
| infill_speed = 80 | |
| interface_shells = 0 | |
| interior_brim_width = 0 | |
| layer_height = 0.333 | |
| match_horizontal_surfaces = 0 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0 | |
| perimeter_speed = 60 | |
| perimeters = 3 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| regions_overlap = 0 | |
| resolution = 0 | |
| seam_position = aligned | |
| shortcuts = support_material | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0 | |
| solid_infill_speed = 20 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 1 | |
| support_material_angle = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_extrusion_width = 0 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = pillars | |
| support_material_spacing = 2.5 | |
| support_material_speed = 60 | |
| support_material_threshold = 60% | |
| thin_walls = 1 | |
| top_infill_extrusion_width = 0 | |
| top_infill_pattern = rectilinear | |
| top_solid_infill_speed = 15 | |
| top_solid_layers = 3 | |
| travel_speed = 130 | |
| xy_size_compensation = 0 | |
| [print:Prusa i3 (0.5,15mm)] | |
| adaptive_slicing = 0 | |
| adaptive_slicing_quality = 75% | |
| avoid_crossing_perimeters = 0 | |
| bottom_infill_pattern = rectilinear | |
| bottom_solid_layers = 3 | |
| bridge_acceleration = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_connections_width = 0 | |
| brim_width = 15 | |
| compatible_printers = | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| external_perimeter_extrusion_width = 0 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0 | |
| fill_angle = 45 | |
| fill_density = 20% | |
| fill_gaps = 1 | |
| fill_pattern = honeycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 200% | |
| first_layer_height = 0.5 | |
| first_layer_speed = 30 | |
| gap_fill_speed = 20 | |
| gcode_comments = 0 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 15% | |
| infill_speed = 80 | |
| interface_shells = 0 | |
| interior_brim_width = 0 | |
| layer_height = 0.5 | |
| match_horizontal_surfaces = 0 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0 | |
| perimeter_speed = 60 | |
| perimeters = 3 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| regions_overlap = 0 | |
| resolution = 0 | |
| seam_position = aligned | |
| shortcuts = support_material | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0 | |
| solid_infill_speed = 20 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 1 | |
| support_material_angle = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_extrusion_width = 0 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = pillars | |
| support_material_spacing = 2.5 | |
| support_material_speed = 60 | |
| support_material_threshold = 60% | |
| thin_walls = 1 | |
| top_infill_extrusion_width = 0 | |
| top_infill_pattern = rectilinear | |
| top_solid_infill_speed = 15 | |
| top_solid_layers = 3 | |
| travel_speed = 130 | |
| xy_size_compensation = 0 | |
| [print:Prusa i3 (1.0,15mm)] | |
| adaptive_slicing = 0 | |
| adaptive_slicing_quality = 75% | |
| avoid_crossing_perimeters = 0 | |
| bottom_infill_pattern = rectilinear | |
| bottom_solid_layers = 3 | |
| bridge_acceleration = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_connections_width = 0 | |
| brim_width = 15 | |
| compatible_printers = | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| external_perimeter_extrusion_width = 0 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0 | |
| fill_angle = 45 | |
| fill_density = 20% | |
| fill_gaps = 1 | |
| fill_pattern = honeycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 200% | |
| first_layer_height = 0.5 | |
| first_layer_speed = 30 | |
| gap_fill_speed = 20 | |
| gcode_comments = 0 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 15% | |
| infill_speed = 80 | |
| interface_shells = 0 | |
| interior_brim_width = 0 | |
| layer_height = 1 | |
| match_horizontal_surfaces = 0 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0 | |
| perimeter_speed = 60 | |
| perimeters = 3 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| regions_overlap = 0 | |
| resolution = 0 | |
| seam_position = aligned | |
| shortcuts = support_material | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0 | |
| solid_infill_speed = 20 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 1 | |
| support_material_angle = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_extrusion_width = 0 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = pillars | |
| support_material_spacing = 2.5 | |
| support_material_speed = 60 | |
| support_material_threshold = 60% | |
| thin_walls = 1 | |
| top_infill_extrusion_width = 0 | |
| top_infill_pattern = rectilinear | |
| top_solid_infill_speed = 15 | |
| top_solid_layers = 3 | |
| travel_speed = 130 | |
| xy_size_compensation = 0 | |
| [print:Prusa i3 (10mm)] | |
| adaptive_slicing = 0 | |
| adaptive_slicing_quality = 75% | |
| avoid_crossing_perimeters = 0 | |
| bottom_infill_pattern = rectilinear | |
| bottom_solid_layers = 3 | |
| bridge_acceleration = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_connections_width = 0 | |
| brim_width = 10 | |
| compatible_printers = | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| external_perimeter_extrusion_width = 0 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0 | |
| fill_angle = 45 | |
| fill_density = 20% | |
| fill_gaps = 1 | |
| fill_pattern = 3dhoneycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 200% | |
| first_layer_height = 0.3 | |
| first_layer_speed = 30 | |
| gap_fill_speed = 20 | |
| gcode_comments = 0 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 15% | |
| infill_speed = 80 | |
| interface_shells = 0 | |
| interior_brim_width = 0 | |
| layer_height = 0.2 | |
| match_horizontal_surfaces = 0 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0 | |
| perimeter_speed = 60 | |
| perimeters = 3 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| regions_overlap = 0 | |
| resolution = 0 | |
| seam_position = aligned | |
| shortcuts = support_material | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0 | |
| solid_infill_speed = 20 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 1 | |
| support_material_angle = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_extrusion_width = 0 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = pillars | |
| support_material_spacing = 2.5 | |
| support_material_speed = 60 | |
| support_material_threshold = 60% | |
| thin_walls = 1 | |
| top_infill_extrusion_width = 0 | |
| top_infill_pattern = rectilinear | |
| top_solid_infill_speed = 15 | |
| top_solid_layers = 3 | |
| travel_speed = 130 | |
| xy_size_compensation = 0 | |
| [print:Prusa i3 (Dual)] | |
| adaptive_slicing = 0 | |
| adaptive_slicing_quality = 75% | |
| avoid_crossing_perimeters = 0 | |
| bottom_infill_pattern = rectilinear | |
| bottom_solid_layers = 3 | |
| bridge_acceleration = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_connections_width = 0 | |
| brim_width = 15 | |
| compatible_printers = | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| external_perimeter_extrusion_width = 0 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0 | |
| fill_angle = 45 | |
| fill_density = 20% | |
| fill_gaps = 1 | |
| fill_pattern = 3dhoneycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 200% | |
| first_layer_height = 0.3 | |
| first_layer_speed = 30 | |
| gap_fill_speed = 20 | |
| gcode_comments = 0 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 2 | |
| infill_extrusion_width = 0 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 15% | |
| infill_speed = 80 | |
| interface_shells = 0 | |
| interior_brim_width = 0 | |
| layer_height = 0.25 | |
| match_horizontal_surfaces = 0 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 1 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0 | |
| perimeter_speed = 60 | |
| perimeters = 3 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| regions_overlap = 0 | |
| resolution = 0 | |
| seam_position = aligned | |
| shortcuts = support_material | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0 | |
| solid_infill_speed = 20 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 1 | |
| support_material_angle = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_extrusion_width = 0 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = pillars | |
| support_material_spacing = 2.5 | |
| support_material_speed = 60 | |
| support_material_threshold = 60% | |
| thin_walls = 1 | |
| top_infill_extrusion_width = 0 | |
| top_infill_pattern = rectilinear | |
| top_solid_infill_speed = 15 | |
| top_solid_layers = 3 | |
| travel_speed = 130 | |
| xy_size_compensation = 0 | |
| [print:Simple Mode] | |
| adaptive_slicing = 0 | |
| adaptive_slicing_quality = 75% | |
| avoid_crossing_perimeters = 0 | |
| bottom_infill_pattern = rectilinear | |
| bottom_solid_layers = 3 | |
| bridge_acceleration = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_connections_width = 0 | |
| brim_width = 0 | |
| compatible_printers = | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| external_perimeter_extrusion_width = 0 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0 | |
| fill_angle = 45 | |
| fill_density = 20% | |
| fill_gaps = 1 | |
| fill_pattern = 3dhoneycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 200% | |
| first_layer_height = 0.35 | |
| first_layer_speed = 30 | |
| gap_fill_speed = 20 | |
| gcode_comments = 0 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 55% | |
| infill_speed = 80 | |
| interface_shells = 0 | |
| interior_brim_width = 0 | |
| layer_height = 0.2 | |
| match_horizontal_surfaces = 0 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0 | |
| perimeter_speed = 60 | |
| perimeters = 3 | |
| post_process = | |
| print_settings_id = | |
| raft_layers = 0 | |
| regions_overlap = 0 | |
| resolution = 0 | |
| seam_position = aligned | |
| shortcuts = support_material | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0 | |
| solid_infill_speed = 20 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 1 | |
| support_material_angle = 0 | |
| support_material_buildplate_only = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_extrusion_width = 0 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = pillars | |
| support_material_spacing = 2.5 | |
| support_material_speed = 60 | |
| support_material_threshold = 60% | |
| thin_walls = 1 | |
| top_infill_extrusion_width = 0 | |
| top_infill_pattern = rectilinear | |
| top_solid_infill_speed = 15 | |
| top_solid_layers = 3 | |
| travel_speed = 130 | |
| xy_size_compensation = 0 | |
| [printer:Prusa i3 (0.3)] | |
| bed_shape = 0x0,200x0,200x200,0x200 | |
| before_layer_gcode = | |
| between_objects_gcode = | |
| end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n | |
| extruder_offset = 0x0 | |
| gcode_flavor = reprap | |
| has_heatbed = 1 | |
| host_type = octoprint | |
| layer_gcode = | |
| max_layer_height = 0.3 | |
| min_layer_height = 0.15 | |
| nozzle_diameter = 0.3 | |
| octoprint_apikey = | |
| pressure_advance = 0 | |
| print_host = | |
| printer_notes = | |
| printer_settings_id = | |
| retract_before_travel = 2 | |
| retract_layer_change = 0 | |
| retract_length = 2 | |
| retract_length_toolchange = 10 | |
| retract_lift = 0 | |
| retract_lift_above = 0 | |
| retract_lift_below = 0 | |
| retract_restart_extra = 0 | |
| retract_restart_extra_toolchange = 0 | |
| retract_speed = 40 | |
| serial_port = | |
| serial_speed = 250000 | |
| start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n | |
| toolchange_gcode = | |
| use_firmware_retraction = 0 | |
| use_relative_e_distances = 0 | |
| use_volumetric_e = 0 | |
| vibration_limit = 0 | |
| wipe = 0 | |
| z_offset = 0 | |
| z_steps_per_mm = 0 | |
| [printer:Prusa i3 (0.3,0.6)] | |
| bed_shape = 0x0,200x0,200x200,0x200 | |
| before_layer_gcode = | |
| between_objects_gcode = | |
| end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n | |
| extruder_offset = 0x0,0x0 | |
| gcode_flavor = reprap | |
| has_heatbed = 1 | |
| host_type = octoprint | |
| layer_gcode = | |
| max_layer_height = 0.3 | |
| min_layer_height = 0.15 | |
| nozzle_diameter = 0.3,0.6 | |
| octoprint_apikey = | |
| pressure_advance = 0 | |
| print_host = | |
| printer_notes = | |
| printer_settings_id = | |
| retract_before_travel = 2,2 | |
| retract_layer_change = 0,0 | |
| retract_length = 2,2 | |
| retract_length_toolchange = 10,10 | |
| retract_lift = 0,0 | |
| retract_lift_above = 0 | |
| retract_lift_below = 0 | |
| retract_restart_extra = 0,0 | |
| retract_restart_extra_toolchange = 0,0 | |
| retract_speed = 40,40 | |
| serial_port = | |
| serial_speed = 250000 | |
| start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n | |
| toolchange_gcode = | |
| use_firmware_retraction = 0 | |
| use_relative_e_distances = 0 | |
| use_volumetric_e = 0 | |
| vibration_limit = 0 | |
| wipe = 0,0 | |
| z_offset = 0 | |
| z_steps_per_mm = 0 | |
| [printer:Prusa i3 (0.6)] | |
| bed_shape = 0x0,200x0,200x200,0x200 | |
| before_layer_gcode = | |
| between_objects_gcode = | |
| end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n | |
| extruder_offset = 0x0 | |
| gcode_flavor = reprap | |
| has_heatbed = 1 | |
| host_type = octoprint | |
| layer_gcode = | |
| max_layer_height = 0.3 | |
| min_layer_height = 0.15 | |
| nozzle_diameter = 0.6 | |
| octoprint_apikey = | |
| pressure_advance = 0 | |
| print_host = | |
| printer_notes = | |
| printer_settings_id = | |
| retract_before_travel = 2 | |
| retract_layer_change = 0 | |
| retract_length = 2 | |
| retract_length_toolchange = 10 | |
| retract_lift = 0 | |
| retract_lift_above = 0 | |
| retract_lift_below = 0 | |
| retract_restart_extra = 0 | |
| retract_restart_extra_toolchange = 0 | |
| retract_speed = 40 | |
| serial_port = | |
| serial_speed = 250000 | |
| start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n | |
| toolchange_gcode = | |
| use_firmware_retraction = 0 | |
| use_relative_e_distances = 0 | |
| use_volumetric_e = 0 | |
| vibration_limit = 0 | |
| wipe = 0 | |
| z_offset = 0 | |
| z_steps_per_mm = 0 | |
| [printer:Prusa i3 (1.0)] | |
| bed_shape = 0x0,200x0,200x200,0x200 | |
| before_layer_gcode = | |
| between_objects_gcode = | |
| end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n | |
| extruder_offset = 0x0 | |
| gcode_flavor = reprap | |
| has_heatbed = 1 | |
| host_type = octoprint | |
| layer_gcode = | |
| max_layer_height = 0.3 | |
| min_layer_height = 0.15 | |
| nozzle_diameter = 1 | |
| octoprint_apikey = | |
| pressure_advance = 0 | |
| print_host = | |
| printer_notes = | |
| printer_settings_id = | |
| retract_before_travel = 2 | |
| retract_layer_change = 0 | |
| retract_length = 2 | |
| retract_length_toolchange = 10 | |
| retract_lift = 0 | |
| retract_lift_above = 0 | |
| retract_lift_below = 0 | |
| retract_restart_extra = 0 | |
| retract_restart_extra_toolchange = 0 | |
| retract_speed = 40 | |
| serial_port = | |
| serial_speed = 250000 | |
| start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n | |
| toolchange_gcode = | |
| use_firmware_retraction = 0 | |
| use_relative_e_distances = 0 | |
| use_volumetric_e = 0 | |
| vibration_limit = 0 | |
| wipe = 0 | |
| z_offset = 0 | |
| z_steps_per_mm = 0 | |
| [printer:Prusa i3 (1.2)] | |
| bed_shape = 0x0,200x0,200x200,0x200 | |
| before_layer_gcode = | |
| between_objects_gcode = | |
| end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n | |
| extruder_offset = 0x0 | |
| gcode_flavor = reprap | |
| has_heatbed = 1 | |
| host_type = octoprint | |
| layer_gcode = | |
| max_layer_height = 0.3 | |
| min_layer_height = 0.15 | |
| nozzle_diameter = 1.2 | |
| octoprint_apikey = | |
| pressure_advance = 0 | |
| print_host = | |
| printer_notes = | |
| printer_settings_id = | |
| retract_before_travel = 2 | |
| retract_layer_change = 0 | |
| retract_length = 2 | |
| retract_length_toolchange = 10 | |
| retract_lift = 0 | |
| retract_lift_above = 0 | |
| retract_lift_below = 0 | |
| retract_restart_extra = 0 | |
| retract_restart_extra_toolchange = 0 | |
| retract_speed = 40 | |
| serial_port = | |
| serial_speed = 250000 | |
| start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n | |
| toolchange_gcode = | |
| use_firmware_retraction = 0 | |
| use_relative_e_distances = 0 | |
| use_volumetric_e = 0 | |
| vibration_limit = 0 | |
| wipe = 0 | |
| z_offset = 0 | |
| z_steps_per_mm = 0 | |
| [printer:TroublemakerMX] | |
| bed_shape = 0x0,200x0,200x200,0x200 | |
| before_layer_gcode = | |
| between_objects_gcode = | |
| end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n | |
| extruder_offset = 0x0,0x0,0x0 | |
| gcode_flavor = reprap | |
| has_heatbed = 1 | |
| host_type = octoprint | |
| layer_gcode = | |
| max_layer_height = 0.3 | |
| min_layer_height = 0.15 | |
| nozzle_diameter = 0.6,0.6,0.6 | |
| octoprint_apikey = | |
| pressure_advance = 0 | |
| print_host = | |
| printer_notes = | |
| printer_settings_id = | |
| retract_before_travel = 2,2,2 | |
| retract_layer_change = 0,0,0 | |
| retract_length = 2,2,2 | |
| retract_length_toolchange = 10,10,10 | |
| retract_lift = 0,0,0 | |
| retract_lift_above = 0 | |
| retract_lift_below = 0 | |
| retract_restart_extra = 0,0,0 | |
| retract_restart_extra_toolchange = 0,0,0 | |
| retract_speed = 40,40,40 | |
| serial_port = | |
| serial_speed = 250000 | |
| start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n | |
| toolchange_gcode = | |
| use_firmware_retraction = 0 | |
| use_relative_e_distances = 0 | |
| use_volumetric_e = 0 | |
| vibration_limit = 0 | |
| wipe = 0,0,0 | |
| z_offset = 0 | |
| z_steps_per_mm = 0 | |
| [settings] | |
| autocenter = 1 |
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| # generated by Slic3r 1.2.9 on Fri Jul 7 16:39:55 2017 | |
| [filament:Simple Mode] | |
| bed_temperature = 110 | |
| extrusion_multiplier = 1 | |
| filament_diameter = 1.75 | |
| first_layer_bed_temperature = 110 | |
| first_layer_temperature = 240 | |
| temperature = 240 | |
| [presets] | |
| filament = Simple Mode.ini | |
| [settings] | |
| autocenter = 1 | |
| mode = simple | |
| [simple] | |
| avoid_crossing_perimeters = 1 | |
| bed_shape = 0x0,180x0,180x180,0x180 | |
| bed_temperature = 110 | |
| before_layer_gcode = | |
| bottom_solid_layers = 3 | |
| bridge_acceleration = 0 | |
| bridge_fan_speed = 100 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_width = 0 | |
| complete_objects = 0 | |
| cooling = 1 | |
| default_acceleration = 0 | |
| disable_fan_first_layers = 3 | |
| dont_support_bridges = 1 | |
| duplicate_distance = 6 | |
| end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n | |
| external_fill_pattern = rectilinear | |
| external_perimeter_extrusion_width = 0 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extruder_offset = 0x0 | |
| extrusion_axis = E | |
| extrusion_multiplier = 1 | |
| extrusion_width = 0 | |
| fan_always_on = 0 | |
| fan_below_layer_time = 60 | |
| filament_colour = #FFFFFF | |
| filament_diameter = 1.75 | |
| fill_angle = 45 | |
| fill_density = 20% | |
| fill_pattern = honeycomb | |
| first_layer_acceleration = 0 | |
| first_layer_bed_temperature = 110 | |
| first_layer_extrusion_width = 200% | |
| first_layer_height = 0.3 | |
| first_layer_speed = 30 | |
| first_layer_temperature = 240 | |
| gap_fill_speed = 20 | |
| gcode_arcs = 0 | |
| gcode_comments = 0 | |
| gcode_flavor = reprap | |
| infill_acceleration = 0 | |
| infill_every_layers = 10 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 15% | |
| infill_speed = 80 | |
| interface_shells = 0 | |
| layer_gcode = | |
| layer_height = 0.2 | |
| max_fan_speed = 100 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_fan_speed = 35 | |
| min_print_speed = 10 | |
| min_skirt_length = 0 | |
| notes = | |
| nozzle_diameter = 0.3 | |
| octoprint_apikey = | |
| octoprint_host = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0 | |
| perimeter_speed = 60 | |
| perimeters = 3 | |
| post_process = | |
| pressure_advance = 0 | |
| raft_layers = 0 | |
| resolution = 0 | |
| retract_before_travel = 2 | |
| retract_layer_change = 0 | |
| retract_length = 2 | |
| retract_length_toolchange = 10 | |
| retract_lift = 0 | |
| retract_restart_extra = 0 | |
| retract_restart_extra_toolchange = 0 | |
| retract_speed = 40 | |
| seam_position = aligned | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| slowdown_below_layer_time = 5 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0 | |
| solid_infill_speed = 20 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = pillars | |
| support_material_spacing = 2.5 | |
| support_material_speed = 60 | |
| support_material_threshold = 0 | |
| temperature = 240 | |
| thin_walls = 1 | |
| threads = 2 | |
| toolchange_gcode = | |
| top_infill_extrusion_width = 0 | |
| top_solid_infill_speed = 15 | |
| top_solid_layers = 3 | |
| travel_speed = 130 | |
| use_firmware_retraction = 0 | |
| use_relative_e_distances = 0 | |
| use_volumetric_e = 0 | |
| vibration_limit = 0 | |
| wipe = 0 | |
| xy_size_compensation = 0 | |
| z_offset = 0 |
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| # generated by Slic3r 1.2.9 on Fri Jul 7 16:39:31 2017 | |
| [filament:Simple Mode] | |
| bed_temperature = 60 | |
| extrusion_multiplier = 1 | |
| filament_diameter = 1.75 | |
| first_layer_bed_temperature = 65 | |
| first_layer_temperature = 210 | |
| temperature = 210 | |
| [presets] | |
| filament = Simple Mode.ini | |
| [settings] | |
| autocenter = 1 | |
| mode = simple | |
| [simple] | |
| avoid_crossing_perimeters = 1 | |
| bed_shape = 0x0,180x0,180x180,0x180 | |
| bed_temperature = 60 | |
| before_layer_gcode = | |
| bottom_solid_layers = 3 | |
| bridge_acceleration = 0 | |
| bridge_fan_speed = 100 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_width = 0 | |
| complete_objects = 0 | |
| cooling = 1 | |
| default_acceleration = 0 | |
| disable_fan_first_layers = 3 | |
| dont_support_bridges = 1 | |
| duplicate_distance = 6 | |
| end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n | |
| external_fill_pattern = rectilinear | |
| external_perimeter_extrusion_width = 0 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extruder_offset = 0x0 | |
| extrusion_axis = E | |
| extrusion_multiplier = 1 | |
| extrusion_width = 0 | |
| fan_always_on = 0 | |
| fan_below_layer_time = 60 | |
| filament_colour = #FFFFFF | |
| filament_diameter = 1.75 | |
| fill_angle = 45 | |
| fill_density = 20% | |
| fill_pattern = honeycomb | |
| first_layer_acceleration = 0 | |
| first_layer_bed_temperature = 65 | |
| first_layer_extrusion_width = 200% | |
| first_layer_height = 0.3 | |
| first_layer_speed = 30 | |
| first_layer_temperature = 210 | |
| gap_fill_speed = 20 | |
| gcode_arcs = 0 | |
| gcode_comments = 0 | |
| gcode_flavor = reprap | |
| infill_acceleration = 0 | |
| infill_every_layers = 10 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 15% | |
| infill_speed = 80 | |
| interface_shells = 0 | |
| layer_gcode = | |
| layer_height = 0.2 | |
| max_fan_speed = 100 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_fan_speed = 35 | |
| min_print_speed = 10 | |
| min_skirt_length = 0 | |
| notes = | |
| nozzle_diameter = 0.3 | |
| octoprint_apikey = | |
| octoprint_host = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0 | |
| perimeter_speed = 60 | |
| perimeters = 3 | |
| post_process = | |
| pressure_advance = 0 | |
| raft_layers = 0 | |
| resolution = 0 | |
| retract_before_travel = 2 | |
| retract_layer_change = 0 | |
| retract_length = 2 | |
| retract_length_toolchange = 10 | |
| retract_lift = 0 | |
| retract_restart_extra = 0 | |
| retract_restart_extra_toolchange = 0 | |
| retract_speed = 40 | |
| seam_position = aligned | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| slowdown_below_layer_time = 5 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0 | |
| solid_infill_speed = 20 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = pillars | |
| support_material_spacing = 2.5 | |
| support_material_speed = 60 | |
| support_material_threshold = 0 | |
| temperature = 210 | |
| thin_walls = 1 | |
| threads = 2 | |
| toolchange_gcode = | |
| top_infill_extrusion_width = 0 | |
| top_solid_infill_speed = 15 | |
| top_solid_layers = 3 | |
| travel_speed = 130 | |
| use_firmware_retraction = 0 | |
| use_relative_e_distances = 0 | |
| use_volumetric_e = 0 | |
| vibration_limit = 0 | |
| wipe = 0 | |
| xy_size_compensation = 0 | |
| z_offset = 0 |
This file contains hidden or bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
| # generated by Slic3r 1.2.9 on Wed Jul 12 10:55:47 2017 | |
| [filament:ABS (Unknown)] | |
| bed_temperature = 105 | |
| bridge_fan_speed = 100 | |
| cooling = 1 | |
| disable_fan_first_layers = 3 | |
| extrusion_multiplier = 1 | |
| fan_always_on = 0 | |
| fan_below_layer_time = 60 | |
| filament_colour = #000000 | |
| filament_diameter = 1.75 | |
| first_layer_bed_temperature = 105 | |
| first_layer_temperature = 255 | |
| max_fan_speed = 100 | |
| min_fan_speed = 35 | |
| min_print_speed = 10 | |
| slowdown_below_layer_time = 5 | |
| temperature = 255 | |
| [filament:ABS (Van Gogh)] | |
| bed_temperature = 105 | |
| bridge_fan_speed = 100 | |
| cooling = 1 | |
| disable_fan_first_layers = 3 | |
| extrusion_multiplier = 1 | |
| fan_always_on = 0 | |
| fan_below_layer_time = 60 | |
| filament_colour = #FFFFFF | |
| filament_diameter = 1.75 | |
| first_layer_bed_temperature = 105 | |
| first_layer_temperature = 255 | |
| max_fan_speed = 100 | |
| min_fan_speed = 35 | |
| min_print_speed = 10 | |
| slowdown_below_layer_time = 5 | |
| temperature = 255 | |
| [filament:PLA (Anet3D)] | |
| bed_temperature = 60 | |
| bridge_fan_speed = 100 | |
| cooling = 1 | |
| disable_fan_first_layers = 3 | |
| extrusion_multiplier = 1 | |
| fan_always_on = 0 | |
| fan_below_layer_time = 60 | |
| filament_colour = #FFFF00 | |
| filament_diameter = 1.75 | |
| first_layer_bed_temperature = 65 | |
| first_layer_temperature = 210 | |
| max_fan_speed = 100 | |
| min_fan_speed = 35 | |
| min_print_speed = 10 | |
| slowdown_below_layer_time = 5 | |
| temperature = 210 | |
| [filament:PLA (Transparent)] | |
| bed_temperature = 60 | |
| bridge_fan_speed = 100 | |
| cooling = 1 | |
| disable_fan_first_layers = 3 | |
| extrusion_multiplier = 1 | |
| fan_always_on = 0 | |
| fan_below_layer_time = 60 | |
| filament_colour = #FFFFFF | |
| filament_diameter = 1.75 | |
| first_layer_bed_temperature = 65 | |
| first_layer_temperature = 210 | |
| max_fan_speed = 100 | |
| min_fan_speed = 35 | |
| min_print_speed = 10 | |
| slowdown_below_layer_time = 5 | |
| temperature = 210 | |
| [filament:Simple Mode] | |
| bed_temperature = 60 | |
| extrusion_multiplier = 1 | |
| filament_diameter = 1.75 | |
| first_layer_bed_temperature = 65 | |
| first_layer_temperature = 210 | |
| temperature = 210 | |
| [presets] | |
| filament = PLA (Transparent).ini | |
| filament_1 = PLA | |
| print = Prusa i3 (0.33,15mm).ini | |
| printer = TroublemakerMX.ini | |
| [print:Prusa i3 (0.2,15mm)] | |
| avoid_crossing_perimeters = 0 | |
| bottom_solid_layers = 3 | |
| bridge_acceleration = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_width = 15 | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| external_fill_pattern = rectilinear | |
| external_perimeter_extrusion_width = 0 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0 | |
| fill_angle = 45 | |
| fill_density = 20% | |
| fill_pattern = 3dhoneycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 200% | |
| first_layer_height = 0.3 | |
| first_layer_speed = 30 | |
| gap_fill_speed = 20 | |
| gcode_comments = 0 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 15% | |
| infill_speed = 80 | |
| interface_shells = 0 | |
| layer_height = 0.2 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0 | |
| perimeter_speed = 60 | |
| perimeters = 3 | |
| post_process = | |
| raft_layers = 0 | |
| resolution = 0 | |
| seam_position = aligned | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0 | |
| solid_infill_speed = 20 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 1 | |
| support_material_angle = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = pillars | |
| support_material_spacing = 2.5 | |
| support_material_speed = 60 | |
| support_material_threshold = 0 | |
| thin_walls = 1 | |
| threads = 2 | |
| top_infill_extrusion_width = 0 | |
| top_solid_infill_speed = 15 | |
| top_solid_layers = 3 | |
| travel_speed = 130 | |
| xy_size_compensation = 0 | |
| [print:Prusa i3 (0.25,15mm)] | |
| avoid_crossing_perimeters = 0 | |
| bottom_solid_layers = 3 | |
| bridge_acceleration = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_width = 15 | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| external_fill_pattern = rectilinear | |
| external_perimeter_extrusion_width = 0 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0 | |
| fill_angle = 45 | |
| fill_density = 20% | |
| fill_pattern = honeycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 200% | |
| first_layer_height = 0.5 | |
| first_layer_speed = 30 | |
| gap_fill_speed = 20 | |
| gcode_comments = 0 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 15% | |
| infill_speed = 80 | |
| interface_shells = 0 | |
| layer_height = 0.25 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0 | |
| perimeter_speed = 60 | |
| perimeters = 3 | |
| post_process = | |
| raft_layers = 0 | |
| resolution = 0 | |
| seam_position = aligned | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0 | |
| solid_infill_speed = 20 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 1 | |
| support_material_angle = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = pillars | |
| support_material_spacing = 2.5 | |
| support_material_speed = 60 | |
| support_material_threshold = 0 | |
| thin_walls = 1 | |
| threads = 2 | |
| top_infill_extrusion_width = 0 | |
| top_solid_infill_speed = 15 | |
| top_solid_layers = 3 | |
| travel_speed = 130 | |
| xy_size_compensation = 0 | |
| [print:Prusa i3 (0.33,15mm)] | |
| avoid_crossing_perimeters = 0 | |
| bottom_solid_layers = 3 | |
| bridge_acceleration = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_width = 15 | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| external_fill_pattern = rectilinear | |
| external_perimeter_extrusion_width = 0 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0 | |
| fill_angle = 45 | |
| fill_density = 20% | |
| fill_pattern = honeycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 200% | |
| first_layer_height = 0.5 | |
| first_layer_speed = 30 | |
| gap_fill_speed = 20 | |
| gcode_comments = 0 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 15% | |
| infill_speed = 80 | |
| interface_shells = 0 | |
| layer_height = 0.333 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0 | |
| perimeter_speed = 60 | |
| perimeters = 3 | |
| post_process = | |
| raft_layers = 0 | |
| resolution = 0 | |
| seam_position = aligned | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0 | |
| solid_infill_speed = 20 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 1 | |
| support_material_angle = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = pillars | |
| support_material_spacing = 2.5 | |
| support_material_speed = 60 | |
| support_material_threshold = 0 | |
| thin_walls = 1 | |
| threads = 2 | |
| top_infill_extrusion_width = 0 | |
| top_solid_infill_speed = 15 | |
| top_solid_layers = 3 | |
| travel_speed = 130 | |
| xy_size_compensation = 0 | |
| [print:Prusa i3 (0.5,15mm)] | |
| avoid_crossing_perimeters = 0 | |
| bottom_solid_layers = 3 | |
| bridge_acceleration = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_width = 15 | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| external_fill_pattern = rectilinear | |
| external_perimeter_extrusion_width = 0 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0 | |
| fill_angle = 45 | |
| fill_density = 20% | |
| fill_pattern = honeycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 200% | |
| first_layer_height = 0.5 | |
| first_layer_speed = 30 | |
| gap_fill_speed = 20 | |
| gcode_comments = 0 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 15% | |
| infill_speed = 80 | |
| interface_shells = 0 | |
| layer_height = 0.5 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0 | |
| perimeter_speed = 60 | |
| perimeters = 3 | |
| post_process = | |
| raft_layers = 0 | |
| resolution = 0 | |
| seam_position = aligned | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0 | |
| solid_infill_speed = 20 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 1 | |
| support_material_angle = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = pillars | |
| support_material_spacing = 2.5 | |
| support_material_speed = 60 | |
| support_material_threshold = 0 | |
| thin_walls = 1 | |
| threads = 2 | |
| top_infill_extrusion_width = 0 | |
| top_solid_infill_speed = 15 | |
| top_solid_layers = 3 | |
| travel_speed = 130 | |
| xy_size_compensation = 0 | |
| [print:Prusa i3 (10mm)] | |
| avoid_crossing_perimeters = 0 | |
| bottom_solid_layers = 3 | |
| bridge_acceleration = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_width = 10 | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| external_fill_pattern = rectilinear | |
| external_perimeter_extrusion_width = 0 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0 | |
| fill_angle = 45 | |
| fill_density = 20% | |
| fill_pattern = 3dhoneycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 200% | |
| first_layer_height = 0.3 | |
| first_layer_speed = 30 | |
| gap_fill_speed = 20 | |
| gcode_comments = 0 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 15% | |
| infill_speed = 80 | |
| interface_shells = 0 | |
| layer_height = 0.2 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0 | |
| perimeter_speed = 60 | |
| perimeters = 3 | |
| post_process = | |
| raft_layers = 0 | |
| resolution = 0 | |
| seam_position = aligned | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0 | |
| solid_infill_speed = 20 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 1 | |
| support_material_angle = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = pillars | |
| support_material_spacing = 2.5 | |
| support_material_speed = 60 | |
| support_material_threshold = 0 | |
| thin_walls = 1 | |
| threads = 2 | |
| top_infill_extrusion_width = 0 | |
| top_solid_infill_speed = 15 | |
| top_solid_layers = 3 | |
| travel_speed = 130 | |
| xy_size_compensation = 0 | |
| [print:Prusa i3 (Dual)] | |
| avoid_crossing_perimeters = 0 | |
| bottom_solid_layers = 3 | |
| bridge_acceleration = 0 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_width = 15 | |
| complete_objects = 0 | |
| default_acceleration = 0 | |
| dont_support_bridges = 1 | |
| external_fill_pattern = rectilinear | |
| external_perimeter_extrusion_width = 0 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extrusion_width = 0 | |
| fill_angle = 45 | |
| fill_density = 20% | |
| fill_pattern = 3dhoneycomb | |
| first_layer_acceleration = 0 | |
| first_layer_extrusion_width = 200% | |
| first_layer_height = 0.3 | |
| first_layer_speed = 30 | |
| gap_fill_speed = 20 | |
| gcode_comments = 0 | |
| infill_acceleration = 0 | |
| infill_every_layers = 1 | |
| infill_extruder = 2 | |
| infill_extrusion_width = 0 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 15% | |
| infill_speed = 80 | |
| interface_shells = 0 | |
| layer_height = 0.25 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_skirt_length = 0 | |
| notes = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 1 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0 | |
| perimeter_speed = 60 | |
| perimeters = 3 | |
| post_process = | |
| raft_layers = 0 | |
| resolution = 0 | |
| seam_position = aligned | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0 | |
| solid_infill_speed = 20 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| support_material = 1 | |
| support_material_angle = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = pillars | |
| support_material_spacing = 2.5 | |
| support_material_speed = 60 | |
| support_material_threshold = 0 | |
| thin_walls = 1 | |
| threads = 2 | |
| top_infill_extrusion_width = 0 | |
| top_solid_infill_speed = 15 | |
| top_solid_layers = 3 | |
| travel_speed = 130 | |
| xy_size_compensation = 0 | |
| [print:Simple Mode] | |
| bottom_solid_layers = 3 | |
| brim_width = 0 | |
| dont_support_bridges = 1 | |
| external_fill_pattern = rectilinear | |
| fill_density = 20% | |
| fill_pattern = 3dhoneycomb | |
| infill_speed = 80 | |
| layer_height = 0.2 | |
| perimeter_speed = 60 | |
| perimeters = 3 | |
| raft_layers = 0 | |
| support_material = 1 | |
| support_material_contact_distance = 0.2 | |
| support_material_spacing = 2.5 | |
| top_solid_layers = 3 | |
| travel_speed = 130 | |
| xy_size_compensation = 0 | |
| [printer:Prusa i3 (0.3)] | |
| bed_shape = 0x0,200x0,200x200,0x200 | |
| before_layer_gcode = | |
| end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n | |
| extruder_offset = 0x0 | |
| gcode_flavor = reprap | |
| layer_gcode = | |
| nozzle_diameter = 0.3 | |
| octoprint_apikey = | |
| octoprint_host = | |
| pressure_advance = 0 | |
| retract_before_travel = 2 | |
| retract_layer_change = 0 | |
| retract_length = 2 | |
| retract_length_toolchange = 10 | |
| retract_lift = 0 | |
| retract_restart_extra = 0 | |
| retract_restart_extra_toolchange = 0 | |
| retract_speed = 40 | |
| start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n | |
| toolchange_gcode = | |
| use_firmware_retraction = 0 | |
| use_relative_e_distances = 0 | |
| use_volumetric_e = 0 | |
| vibration_limit = 0 | |
| wipe = 0 | |
| z_offset = 0 | |
| [printer:Prusa i3 (0.3,0.6)] | |
| bed_shape = 0x0,200x0,200x200,0x200 | |
| before_layer_gcode = | |
| end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n | |
| extruder_offset = 0x0,0x0 | |
| gcode_flavor = reprap | |
| layer_gcode = | |
| nozzle_diameter = 0.3,0.6 | |
| octoprint_apikey = | |
| octoprint_host = | |
| pressure_advance = 0 | |
| retract_before_travel = 2,2 | |
| retract_layer_change = 0,0 | |
| retract_length = 2,2 | |
| retract_length_toolchange = 10,10 | |
| retract_lift = 0,0 | |
| retract_restart_extra = 0,0 | |
| retract_restart_extra_toolchange = 0,0 | |
| retract_speed = 40,40 | |
| start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n | |
| toolchange_gcode = | |
| use_firmware_retraction = 0 | |
| use_relative_e_distances = 0 | |
| use_volumetric_e = 0 | |
| vibration_limit = 0 | |
| wipe = 0,0 | |
| z_offset = 0 | |
| [printer:Prusa i3 (0.6)] | |
| bed_shape = 0x0,200x0,200x200,0x200 | |
| before_layer_gcode = | |
| end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n | |
| extruder_offset = 0x0 | |
| gcode_flavor = reprap | |
| layer_gcode = | |
| nozzle_diameter = 0.6 | |
| octoprint_apikey = | |
| octoprint_host = | |
| pressure_advance = 0 | |
| retract_before_travel = 2 | |
| retract_layer_change = 0 | |
| retract_length = 2 | |
| retract_length_toolchange = 10 | |
| retract_lift = 0 | |
| retract_restart_extra = 0 | |
| retract_restart_extra_toolchange = 0 | |
| retract_speed = 40 | |
| start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n | |
| toolchange_gcode = | |
| use_firmware_retraction = 0 | |
| use_relative_e_distances = 0 | |
| use_volumetric_e = 0 | |
| vibration_limit = 0 | |
| wipe = 0 | |
| z_offset = 0 | |
| [printer:TroublemakerMX] | |
| bed_shape = 0x0,200x0,200x200,0x200 | |
| before_layer_gcode = | |
| end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n | |
| extruder_offset = 0x0,0x0,0x0 | |
| gcode_flavor = reprap | |
| layer_gcode = | |
| nozzle_diameter = 0.6,0.6,0.6 | |
| octoprint_apikey = | |
| octoprint_host = | |
| pressure_advance = 0 | |
| retract_before_travel = 2,2,2 | |
| retract_layer_change = 0,0,0 | |
| retract_length = 2,2,2 | |
| retract_length_toolchange = 10,10,10 | |
| retract_lift = 0,0,0 | |
| retract_restart_extra = 0,0,0 | |
| retract_restart_extra_toolchange = 0,0,0 | |
| retract_speed = 40,40,40 | |
| start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n | |
| toolchange_gcode = | |
| use_firmware_retraction = 0 | |
| use_relative_e_distances = 0 | |
| use_volumetric_e = 0 | |
| vibration_limit = 0 | |
| wipe = 0,0,0 | |
| z_offset = 0 | |
| [settings] | |
| autocenter = 1 | |
| mode = expert | |
| [simple] | |
| avoid_crossing_perimeters = 1 | |
| bed_shape = 0x0,180x0,180x180,0x180 | |
| bed_temperature = 60 | |
| before_layer_gcode = | |
| bottom_solid_layers = 3 | |
| bridge_acceleration = 0 | |
| bridge_fan_speed = 100 | |
| bridge_flow_ratio = 1 | |
| bridge_speed = 60 | |
| brim_width = 0 | |
| complete_objects = 0 | |
| cooling = 1 | |
| default_acceleration = 0 | |
| disable_fan_first_layers = 3 | |
| dont_support_bridges = 1 | |
| duplicate_distance = 6 | |
| end_gcode = M104 S0 ; turn off temperature\nG28 X0 ; home X axis\nM84 ; disable motors\n | |
| external_fill_pattern = rectilinear | |
| external_perimeter_extrusion_width = 0 | |
| external_perimeter_speed = 50% | |
| external_perimeters_first = 0 | |
| extra_perimeters = 1 | |
| extruder_clearance_height = 20 | |
| extruder_clearance_radius = 20 | |
| extruder_offset = 0x0 | |
| extrusion_axis = E | |
| extrusion_multiplier = 1 | |
| extrusion_width = 0 | |
| fan_always_on = 0 | |
| fan_below_layer_time = 60 | |
| filament_colour = #FFFFFF | |
| filament_diameter = 1.75 | |
| fill_angle = 45 | |
| fill_density = 20% | |
| fill_pattern = honeycomb | |
| first_layer_acceleration = 0 | |
| first_layer_bed_temperature = 65 | |
| first_layer_extrusion_width = 200% | |
| first_layer_height = 0.3 | |
| first_layer_speed = 30 | |
| first_layer_temperature = 210 | |
| gap_fill_speed = 20 | |
| gcode_arcs = 0 | |
| gcode_comments = 0 | |
| gcode_flavor = reprap | |
| infill_acceleration = 0 | |
| infill_every_layers = 10 | |
| infill_extruder = 1 | |
| infill_extrusion_width = 0 | |
| infill_first = 0 | |
| infill_only_where_needed = 0 | |
| infill_overlap = 15% | |
| infill_speed = 80 | |
| interface_shells = 0 | |
| layer_gcode = | |
| layer_height = 0.2 | |
| max_fan_speed = 100 | |
| max_print_speed = 80 | |
| max_volumetric_speed = 0 | |
| min_fan_speed = 35 | |
| min_print_speed = 10 | |
| min_skirt_length = 0 | |
| notes = | |
| nozzle_diameter = 0.3 | |
| octoprint_apikey = | |
| octoprint_host = | |
| only_retract_when_crossing_perimeters = 1 | |
| ooze_prevention = 0 | |
| output_filename_format = [input_filename_base].gcode | |
| overhangs = 1 | |
| perimeter_acceleration = 0 | |
| perimeter_extruder = 1 | |
| perimeter_extrusion_width = 0 | |
| perimeter_speed = 60 | |
| perimeters = 3 | |
| post_process = | |
| pressure_advance = 0 | |
| raft_layers = 0 | |
| resolution = 0 | |
| retract_before_travel = 2 | |
| retract_layer_change = 0 | |
| retract_length = 2 | |
| retract_length_toolchange = 10 | |
| retract_lift = 0 | |
| retract_restart_extra = 0 | |
| retract_restart_extra_toolchange = 0 | |
| retract_speed = 40 | |
| seam_position = aligned | |
| skirt_distance = 6 | |
| skirt_height = 1 | |
| skirts = 1 | |
| slowdown_below_layer_time = 5 | |
| small_perimeter_speed = 15 | |
| solid_infill_below_area = 70 | |
| solid_infill_every_layers = 0 | |
| solid_infill_extruder = 1 | |
| solid_infill_extrusion_width = 0 | |
| solid_infill_speed = 20 | |
| spiral_vase = 0 | |
| standby_temperature_delta = -5 | |
| start_gcode = G28 ; home all axes\nG1 Z5 F5000 ; lift nozzle\n | |
| support_material = 0 | |
| support_material_angle = 0 | |
| support_material_contact_distance = 0.2 | |
| support_material_enforce_layers = 0 | |
| support_material_extruder = 1 | |
| support_material_extrusion_width = 0 | |
| support_material_interface_extruder = 1 | |
| support_material_interface_layers = 3 | |
| support_material_interface_spacing = 0 | |
| support_material_interface_speed = 100% | |
| support_material_pattern = pillars | |
| support_material_spacing = 2.5 | |
| support_material_speed = 60 | |
| support_material_threshold = 0 | |
| temperature = 210 | |
| thin_walls = 1 | |
| threads = 2 | |
| toolchange_gcode = | |
| top_infill_extrusion_width = 0 | |
| top_solid_infill_speed = 15 | |
| top_solid_layers = 3 | |
| travel_speed = 130 | |
| use_firmware_retraction = 0 | |
| use_relative_e_distances = 0 | |
| use_volumetric_e = 0 | |
| vibration_limit = 0 | |
| wipe = 0 | |
| xy_size_compensation = 0 | |
| z_offset = 0 |
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment