Leo-PL

J5 is the Tag-Connect footprint, with ordering like this:

|---------------|
| O           O ----|
|    2 4 6 8 10 o   |
| o                 |
|    1 3 5 7 9  o   |
| O           O ----| J5
|---------------|
     ^

Leo-PL

#!/usr/bin/env python3
#
# Simple Intel x520 EEPROM patcher
# Modifies the EEPROM to unlock the card for non-intel branded SFP modules.
#
# Copyright 2020,2021,2022 Andreas Thienemann <andreas@bawue.net>
#
# Licensed under the GPLv3
#
# Based on research described at https://forums.servethehome.com/index.php?threads/patching-intel-x520-eeprom-to-unlock-all-sfp-transceivers.24634/

Leo-PL

#!/bin/sh

CONFIGFS=/sys/kernel/config/usb_gadget/g1
USB_VENDORID="0x1D6B"  # Linux Foundation
USB_PRODUCTID="0x0104" # Multifunction composite gadget
USB_MANUF="Debian"
USB_PRODUCT="Mobile USB Gadget"
USB_SERIAL=$(sha256sum < /etc/machine-id | cut -d' ' -f1)
USB_ATTRIBUTES="0x80" # Bus-powered
USB_MAX_POWER="500" # mA

Leo-PL

[ "${ACTION}" = "add" -o "${ACTION}" = "remove" ] || exit 0
[ "${SUBSYSTEM}" = "tty" ] || exit 0
[ -n "${DEVNAME}" -a -n "${DEVPATH}" ] || exit 1

if [ "${ACTION}" = "add" ]; then
        subsystem="$(basename $(readlink /sys${DEVPATH}/../../../subsystem))"

        [ "$subsystem" = "usb" ] || exit 0

        manufacturer="$(cat /sys${DEVPATH}/../../../../manufacturer)" || manufacturer="$(cat /sys${DEVPATH}/../../../../idVendor)"

Leo-PL

[Unit]
Description=Network UPS Tools - power device driver controller
After=local-fs.target network.target systemd-udev-settle.service
Wants=systemd-udev-settle.service
StopWhenUnneeded=yes

[Service]
ExecStart=/sbin/upsdrvctl start %i
ExecStop=/sbin/upsdrvctl stop %i
Type=forking

Leo-PL

[Unit]
Description=Software Defined Radio TCP Server
Requires=network.target
After=network.target

[Service]
ExecStart=/bin/sh -c "/usr/bin/rtl_tcp -a 0.0.0.0 -d %i -p $$((1234+%i))"
Restart=on-failure
KillMode=control-group

Leo-PL

#!/usr/bin/python3

# Original script by frutis, mods by Leo-PL
# Usage: 
# 1. uncomment proper section for your router (MF283+, MF286, MF286A, MF286D).
# 2. set correct IME if you have one
# 3. Set correct version ID (the integrate_version from NVRAM) for your device if not already found here
# 4. Run the script - it shall return the URL of data update, if available for the set base version.

from base64 import b64decode, b64encode

Leo-PL

README
A simple rule to push sensor data to Luftdaten directly off of sensor running Tasmota. Assumes configured BME280 and PMS5003 sensors.
Replace <CHIP_ID> and <VERSION> by ESP8266 chip ID (available on info page) and Tasmota version, respectively.

Rule1
ON Tele-BME280#Temperature DO Backlog Var1 %value% ENDON
ON Tele-BME280#Humidity DO Backlog Var2 %value% ENDON
ON Tele-BME280#Pressure DO Backlog Var3 %value% ENDON
ON Tele-PMS5003#PM10 DO Backlog Var4 %value% ENDON
ON Tele-PMS5003#PM2.5 DO

Leo-PL

# Creates persistent serial port symlinks for USB devices,
# like mobile broadband modems, USB-UART bridges, etc,
# with layout very similar to udev symlinks
# Put under /etc/hotplug.d/tty

[ "${ACTION}" = "add" -o "${ACTION}" = "remove" ] || exit 0
[ "${SUBSYSTEM}" = "tty" ] || exit 0
[ -n "${DEVNAME}" -a -n "${DEVPATH}" ] || exit 1

if [ "${ACTION}" = "add" ]; then

Leo-PL

#!/bin/bash

# Simple script to check if remote host behind a jump host is up. If not - wake it up using etherwake.
# Usage: invoke the script through ProxyCommand directive from your ssh_config.
# "nc" must be available on your host. "etherwake" must be available on jump host.
# Example: 
# Host <target_hostname> 
#       ProxyCommand ~/.ssh/ssh-wakeup.sh <jumphost_address> <wol_interface> <wol_mac_address> %h %p

function wait_for_host() {